Question about 1994 Mercury Grand Marquis

1 Answer

Need to do oil change. can not find oil pan. where is it located

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 17,970 Answers


1. Remove the upper radiator hose. Remove the wiper module and support bracket.

  1. Disconnect and plug the compressor outlet hose at the compressor and remove the bolt retaining the hose assembly to the right coil bracket. Cap the compressor outlet.
  2. Remove the engine harness connector from the retaining bracket on the brake vacuum booster and detach the connector and transmission harness connector.
  3. Disconnect the throttle valve cable from the throttle body and disconnect the heater outlet hose.
  4. Remove the nut retaining the ground strap to the right cylinder head. Remove the upper stud and loosen the lower bolt retaining the heater outlet hose to the right cylinder head and position out of the way.
  5. Remove the blower motor resistor. Remove the bolt retaining the right engine mount to the lower engine bracket.
  6. Disconnect the vacuum hoses from the EGR valve and tube. Remove the 2 bolts retaining the EGR valve to the intake manifold.
  7. Raise and safely support the vehicle. Drain the crankcase and remove the engine mount through bolts.
  8. Remove the EGR tube line nut from the right exhaust manifold and remove the EGR valve and tube assembly.
  9. Disconnect the exhaust from the exhaust manifolds. Lower the exhaust system and support it with wire from the crossmember.
  10. Position a jack and a block of wood under the oil pan, rearward of the oil drain hole. Raise the engine approximately 4 in. and insert 2 wood blocks approximately 2 1 / 2 in. thick under each engine mount. Lower the engine onto the wood blocks and remove the jack.
  11. Remove the 16 bolts retaining the oil pan to the engine block and remove the oil pan.

It may be necessary to loosen, but not remove, the 2 nuts on the rear transmission mount and with a jack, raise the transmission extension housing slightly to remove the pan.
  1. If necessary, remove the 2 bolts retaining the oil pickup tube to the oil pump and remove the bolt retaining the pickup tube to the main bearing stud spacer. Remove the pickup tube.



need to do oil change. - 20871a3.jpg

Fig. 3: Oil pan bolt torque sequence-4.6L engine (click over pic fo zoom).


Hpe helps (remember to rate this).

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is transmission filter located in 2001 mitsubishi diamante located and how do i change it?


transmission filter in the bottom of transmission bolted to valve body.you need a large drain pan.place drain plug under transmission oil pan.remove transmission oil pan drain plug.let all transmission fluid drain out then screw back drain plug in oil pan.then you need to remove transmission oil pan then remove filter and replace pan gasket also.make sure you have right amount transmission fluid on hand.buy extra because if you short of fluid you cant drive car if fluid level too low.make sure you get the right amount fluid.torque pan bolts to 96 inch pounds.

Nov 10, 2011 | 2001 Mitsubishi Diamante

4 Answers

Where is the oil pump located on a 1998 Chevy S-10?


Please don't forget to rate! Thanks!

Exploded view of a common oil pump mounting-4.3L engine shown, it is the bottom of your engine, located under your oil pan.


c17hydro_150.gif

Exploded view of a common oil pump mounting-2.2L engine shown, located under your oil pan.





c17hydro_151.gif

Apr 19, 2011 | Chevrolet S 10 Cars & Trucks

2 Answers

I am changing the oil my self and want to know which screw to unscrew under the car. i need a diagram to release the the oil from the bottom. where do i find one?


2006 uplander, there maybe a cover to remove to get to the oil pan, lets see if i can find a picture of the drain plug.okay im not sure the engine size in this uplander but they all should be about the same, here are some diagrams to help you locate the oil filter and oil pan drain plug. the oil filter is located from under the engine on the driverside behind the ac compressor, the oil drain plug is located on the bottom of the oil pan on the pass/side. heres a diagram of the two . hope this helps.johnjohn2_90.gifjohnjohn2_91.gifjohnjohn2_92.gif

Mar 20, 2011 | 2006 Chevrolet Uplander

2 Answers

1986 Chevy S-10 5 speed, where is my oil pump?


It's located to the rear part of the oil pan. To change it, the oil pan needs to be removed. To do this, the engine needs to be raised, or the transmission needs to be removed. Make sure it is the problem before just "changing" it.

Nov 12, 2010 | 1986 Chevrolet S-10 Blazer

2 Answers

I AM LOOKING WHERE IS THE OIL PUMP IN 2003 KIA SEDONA ENGINE


take the sump off and you will find it ,to get the sump off you will need to remove the engine

Jun 27, 2010 | 2003 Kia Sedona

1 Answer

Change oil pan gasket


YOUR OIL PAN GASKET IS ATTACH TO TOP OF OIL PAN.WHICH SEAL TO ENGINE BLOCK.YOU NEED A HAYNES REPAIR BECAUSE YOU HAVE TO REMOVE RIGHT MANY THINGS TO GET OIL PAN OFF TO GET TO GASKET.

Feb 23, 2010 | 1999 Oldsmobile Alero

3 Answers

Whear is the oil drain plug on a 92 previa as the oil change light stays on and their is plenty of oil in boath chambers


the drain plug is on the oil pan under the van. check your owners manual or google oil change reset for your verhicle to reset the change oil light the change oil indicator should come on every 3000 miles and be reset after every oil change

Feb 09, 2010 | 1997 Toyota Previa

1 Answer

Can't locate reserve oil drain plug on 1994 Ford E350


It only has 1 oil pan which is call a dual resreve. One oil plug is a the bottom of the pan the other is at the front of the oil pan. Look at the front of the oil pan for the other drain plug. Make sure on how many quarts of oil it takes. ( I know 5.0 take 5 quarts including oil filter. But then again its a van double check)

Mar 22, 2009 | 2002 Ford E350

Not finding what you are looking for?
1994 Mercury Grand Marquis Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...