Question about 1994 Isuzu Rodeo

1 Answer

Fuel gage is not reading the amount of fuel in the tank. It either reads completely full or completelr empty.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Sounds like the sending unit in the gas tank may be the problem. The other possibility may be the guage but usually the sending unit goes first.

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel gage showing half a tank but trip computer only registering 60 miles left


Its very simple. If the gauge is showing half full then fill the tank and see how much fuel it takes. If the amount you add is approximately 50 percent of the fuel tank capacity then you know the fuel gauge is accurate . In that case the computer is giving an inaccurate reading and should be ignored. All you need is an accurate fuel gauge - it does not matter a row of beans what the computer says if the fuel gauge is reading correctly.

Dec 22, 2012 | Saab Cars & Trucks

1 Answer

Fuel guage not working


Testing the fuel gage requires accessing the harness from the fuel pump and grounding the yellow / white wire with 160 ohms resistance this should cause the gage to read full, and with the circuit open you should have the gage reading empty. If the gage works in this order then the likely failure is the sending unit in the tank , and will require replacement.

May 30, 2010 | 1999 Ford Expedition

2 Answers

Gas gage read full when empty and sometimes emty


You have a bad fuel level sensor.The fuel tank needs to come out and the sensor replaced.You don`t have to replace the pump assembly.You can get the level sensor separate.I`m not sure if the parts stores have it but I know the dealerships do.Hope this helps.Good luck.

Mar 16, 2010 | 2004 Pontiac Montana

2 Answers

Gmc jimmy 1999, fuel gauge reading empty, even


the sending unit in the tank has gone bad or a wire is grounded out.

Feb 06, 2010 | 1999 GMC Jimmy

1 Answer

1987 ford f150 dual fuel tanks fuel qty gages inop.fwd tank reads empty and when aft selected reads full.


tank switch on dash could be bad, also selector valve could be bad. are the fuel gauges accurate front or rear. like you say the rear reads full, is it?? I would try the switch on the dash first.

Sep 17, 2009 | 1987 Ford F 150

2 Answers

Even with a full tank my 2005 Envoy XUV fuel light stays on and fuel gauge marks empty


u need to change this gauge or try to dissasseble and clean it very well then try to install it back again

Jun 06, 2009 | 2005 GMC Envoy Xl

2 Answers

I have a 94 chevy s10 and my gas reads empty while i drive.but when i shut off the truck the gauge moves to different readings.


Is......the problem--"the gas gage reads empty when there is fuel in the tank. OR, The gage moves when the key to turned off ?

If it's the first,
You will need to test the gage and through process of elimination, determin if the Sending unit inside the fuel tank has gone Bad.

If its the second ? - Electrical gauges will move when powered down. Normal

Testing the gauge may not be easy - just depends on your ability.
It is a simple 2-wire gauge circuit, when disconnect (usually need the fuel tank) the gage reads in one direction (either full or empty)
then when shorted-the gage reads in oppisite direction.

Of course you must select the correct wires or you may short out the wrong circuits!! Most GM vehicles use a purple wire & black wire.

A quick method I have used to check the in-take part of the gauge is this.
1st. know there is gas - 1/2 tank works best.
2nd driver's door open, key in run position, engine not running.
3rd gently lift up on the door then let if come back down, gently.
just enough to cause the gas to slosh around.
4th - keep an eye on the gas gage, a bad sending unit in the take will show up as a "twitchy" needle.

Of course, if the gage never leaves empty - sloshing won't work.
I have a known good sending unit I can plug into the vehicle and simulate different levels of fuel - if the gas gage works, I know the problem is in the tank.

Let us know.

Dave

Feb 28, 2009 | 1996 GMC Sonoma

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...