Question about 1998 Ford Contour

1 Answer

1998 contuor belt keeps jumping - 1998 Ford Contour

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,299 Answers

The belt keeps jumping is a problem when one of the pulley's are out of alignment. Or the idler pulley is worn out.

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Zx2 ran fine for a bit after timing belt change, now no start.


suspect the timing belt tension was to low and has jumped a few teeth initially(run rough) and then jumped further or stripped teeth(will not start at all).
check timing belt position setup....
if its 1-2 teeth out of timing you could put a new belt on with engine correctly setup.
.if its completely wrong the your engine will have internal damage(valves bent and pistons dented)

Nov 17, 2013 | 1998 Ford Escort

1 Answer

New serpentine belt keeps jumping off


Hi Daniel,Sounds like your belt tensioner is bad and not keeping proper tension on belt,Here is a picture of the belt tensioner,and here's your belt diagram.

Feb 01, 2013 | 1989 GMC Sierra

1 Answer

I have a 1998 Dodge Stratus ES and am having problems getting the timeing belt on. Can somebody please explain how we may put the belt back on without a bunch of trouble?


Make sure your timing marks are lined up and start putting your belt on the rear cam first that would be 1,3,5 cam. Then route it under the water pump and up around the front cam 2,4,6 cam being careful the rear cam don't jump off it's mark. Keep tension on the belt while routing it. Continue routing it over the idler pulley keeping tension on it route it down and around the crank sprocket. Now set your tension pulley and replace the tension pin. Once the belt is set hand crank the engine 2 to 3 complete cycles then recheck your marks. This is for a 2.5 engine. Good luck hope this helps.

Jun 20, 2011 | 1998 Dodge Stratus

1 Answer

Timming belt / jump time want to repace belt


honda DOHC and SOHC motors have "zero tolerance" motors, this means if they "jump timing" they need to be inspected for head/valve damage, have this done before spending money on replacing the timing belt

Mar 01, 2011 | 1998 Honda Passport

3 Answers

How to fix ford contour code p0708


this code indicates a problem with the transmission range selected switch, this switch is on the transmission case where the shift cable attaches, when u select a gear it sends a signal to the computer control that u want lets say Reverse by sensing the range selector switch feedback, replace the switch will most likely cure the code, then clear the code and drive a few miles.

Jul 22, 2010 | 1995 Ford Contour

2 Answers

Timing belt jumped... why?


This can be caused by not tensioning the belt corectly.When fitting a new belt you should allways replace the tensioner,and make sure the water pump pulley is in good working order.Its always wise to get your timming belt from the dealer.as others are nown to be faulty.Fit new belt follow manuel when doing so.good luck

Aug 01, 2009 | 1998 Ford Escort

1 Answer

1998 Firebird fuel filter


Need more information. Has car been sitting? Is it getting fuel to the intake? ( injector or throttle body?) What engine does it have? What type of carb. does it have? fuel injection, carb., or throttle body? Pull off a plug wire, and check it for spark....does ignition spark? Check timing for jumping. could have jumped timing belt? you need someone to help you visualize and troubleshoot.

Jul 16, 2009 | 1998 Pontiac Firebird

1 Answer

98 Audi A6, Battery died overnight, when jumping smoke rises


Sounds like the alternator is badly damaged. The alternator will drain the battery if the regulutor or diode assembly goes out and/or the alternator is seized or locking up, which will cause the smoke (belt slippage) and drag on the engine (rough idle).

Apr 06, 2009 | 1998 Audi A6

2 Answers

1998 escort serpintine belt keeps slipping off pulleys!


look at the belt tensioner while the car is running and see if it is jumping up and down and if it is replace the tensioner

Jan 29, 2009 | 1998 Ford Escort

Not finding what you are looking for?
1998 Ford Contour Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...