Question about 2006 Pontiac Montana SV6

Open Question

I NEED TO REPLACE THE FRONT LEFT TURNING SIGNAL LIGHT BULB IN MY 2006 MONTANA VAN. hOW DO i REMOVE THE HEADLIGHT ASSEMBLY SO I CAN THEN ACCESS THE LOWER TURN SIGNAL LIGHT?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Left front turn signal bulb for 2001 Pontiac Montana

There is only one screw to remove that releases the mounting tab at the upper inner corner of the assembly. That screw has a plastic wingnut molded onto it so you can turn by hand. Once that is removed, the assembly can be pulled straight forward. At the inner bottom corner, a spring clip faces straight rearward. Pull with enough force to to release the clip from its slot. Only two "Fingers" hold the rear of the assembly in the sheet metal holes.

Posted on Nov 15, 2008

  • 840 Answers

SOURCE: Trying to remove headlight assembly to change turn signal bulb on

you need to take off front bumper to get the bottom bolt

Posted on Jan 24, 2009

  • 1 Answer

SOURCE: Removing Headlight assembly

There is a small hex headed fastener behind the headlight, oriented vertically. Loosen this and remove it, it is long and passes through the body of the light housing to threads below. You then pull the headlight housing forward, its still held in place by several friction fasteners so it may take a little force but it will "pop" off and then when you're through you'll have to "pop" in back in.

Posted on Jan 13, 2009

  • 840 Answers

SOURCE: How do you access the

if their is a engine cover take cover off / their are 2 bolts for the headlight take them out and pull the headlight forward

Posted on Jan 25, 2009

  • 5 Answers

SOURCE: 99 cutlass supreme headlight bulb replacement

Look at the top of the headlight assembly. There is a plastic panel on top of the assembly that is held in place by two plastic pins. Remove those pins by lifting the center of the pin and then pull out the pin. Remove the panel. Then you will find two small plastic levers that will lift about 1/2 inch. They do not come out but they will release two studs that secure the assembly. After the assembly is released, slide it forward to access the bulbs you need to replace. Installation is the reverse of these procedures.

Posted on Mar 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the globe to the headlight of my Kia Pregio GS 2005 van


To replace headlight bulb of kia pregio van: You only need Phillips screw driver and 10mm socket or open wrench. Open the hood, remove front grill with 4 phillips screw. This will give you room for your hand to pull out the headlight housing later on. Next is remove the signal light housing by unscrewing the phillips screw on top of the headlight housing then pull out the signal light housing and remove the bulb. You will see 2 pcs 10mm bolts on the side which hold the headlight. Loosened and remove the bolts on headlight holder then pull the headlight sideward. Remove power supply socket before removing it completely from the van. Remove bulb socket, spring clip, and busted bulb and replace with new one. Reassemble the disassembled parts in reverse order. That's it, will take you only 10 minutes.

May 27, 2011 | Kia Rio Cars & Trucks

1 Answer

How to replace head light


The headlight replacement procedure.:---
  • Apply the parking brake and open the hood.The head is attached by thumb shaped screw.You will see the thumb screw on the upper inboard corner of the turn signal assembly Remove the screw with the screwdriver.Pull the turn signal assembly outward away from the fender and then disconnect the bulb.Turning the socket and wire 1/4- counterclockwise. Set the turn signal assembly aside.Disconnect the electrical connector plug from the headlight being replaced. Lift up on the blue retaining clip of the plug and pull it away from the socket of the headlight.Turn the black retaining collar of the headlight counterclockwise to remove it and the headlight from the headlight assembly.Install the new headlight by reversing the procedure.Replace the turn signal bulb into its assembly and reinstall the assembly and thumbscrew.

    Thanks.Helpmech.



  • Nov 12, 2010 | 2005 Pontiac Montana SV6

    2 Answers

    How do you replace the front turn signal on a 2005 Buick Terraza?


    Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

    I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

    Sep 07, 2010 | 2005 Buick Terraza

    1 Answer

    2000 pontiac montana. I want to replace the driving ligh bulbs. the under the headlights what size is it?


    Fog/Driving Light Bulb Size: 880
    Here is the rest of the bulb size used in your Montana.
    2000 Pontiac Montana Auto Light Bulb Diagram
    Low Beam Headlight Bulb Size: 9004
    High Beam Headlamp Light Bulb Size: 9004
    Parking Light Bulb Size: 4157NALL
    Front Turn Signal Light Bulb Size: 4157NALL
    Rear Turn Signal Light Bulb Size: 3156
    Tail Light Bulb Size: 3057
    Stop Light Bulb Size: 3057
    High Mount Stop Light Bulb Size: Assembly
    Fog/Driving Light Bulb Size: 880
    License Plate Light Bulb Size: 168
    Back Up Light Bulb Size: 3156
    Front Sidemarker Light Bulb Size: 194
    Ash Tray Light Bulb Size: 558
    Glove Box Light Bulb Size: 194
    Map Light Bulb Size: 168
    Dome Light Bulb Size: 562
    Step/Courtesy Light Bulb Size: 168
    Trunk/Cargo Area Light Bulb Size: 212-2
    Daytime Running Light Bulb Size: 3157NALL
    Thank you for using fixya.


    Apr 30, 2010 | 2000 Pontiac Montana

    1 Answer

    Cobalt 2005 ls headlight bulb replacement


    Instructions Things You'll Need:
    • 9007 LL halogen headlight bulb
    • Wrench
    • Gloves or clean rag
    1. Step 1 Set the parking brake and remove the keys from the ignition to ensure your Chevy Cobalt won't roll while you're replacing the headlight bulb.
    2. Step 2 Open the hood by pulling the hood release latch located under the instrument panel on the driver's side of the car. Locate the secondary release latch on the front of the hood at the center, slightly towards the driver's side. Slide the latch to the left to release the hood and raise it.
    3. Step 3 Locate the headlight assembly and remove the bolts by turning them counterclockwise. Set the bolts aside in a safe place, so you won't misplace them.
    4. Step 4 Remove the plastic fasteners from the headlight assembly molding. Carefully pull back the front fascia, or molding. You may need an extra pair of hands to perform this slightly awkward task.
    5. Step 5 Grab the headlight assembly and pull it towards the radiator at a slight angle to remove it. This should provide easier access to the headlight bulb and wiring harness.
    6. Step 6 Lift the plastic locking tab on the wiring harness to disconnect the bulb base. Then, disconnect the wiring harness from the bulb socket and remove the black retainer by turning it counterclockwise.
    7. Step 7 Disconnect the bulb socket by turning it counterclockwise. Remove the old bulb from the socket by firmly, but gently pulling it straight out.
    8. Step 8 Replace the old bulb with a new 9007 LL halogen headlight bulb. Put your headlight assembly back together by reversing the steps when you disassembled it. Use 89 inch-lb torque when retightening the headlight assembly

    Feb 26, 2010 | 2006 Chevrolet Cobalt

    3 Answers

    I need to change the left front turn signal bulb on a 2006 Cadillac SRX? Looks difficult. Paul LeMaster


    hi Paul

    Should be able to open the hood remove plastic headlight cover & pull pins (2) on light assembly whole light assembly will pull out then replace turn signal.

    Good luck.

    Dec 02, 2009 | 2006 Cadillac SRX

    1 Answer

    How do i install a new front turn signal bulb on my 2000 pontiac montana


    You have to remove the headlight assembly to remove the turn light assemble. There are two mounting bolts that hold the headlight assembly to the frame that needs to be removed and one mounting bolt that holds the turn signal light assembly on the headlight assembly that needs to be removed. Once all three bolts (black plastic in colour with a wing nut) have been removed the headlight and turn signal assembly can just be removed. Take note that the assembly has a guild slot to be guild in place back when re installing the head light and turn signal assembly. Good luck and hope this helps. Keep me posted and I'll try to explain in a different way if i was un clear, Harder to explain then doing the job it self. 

    Jul 20, 2009 | 2000 Pontiac Montana

    1 Answer

    Signal light change.


    There is one 10mm Bolt on the top of the light and three 10mm nuts on the back of the light. You will need to use a 10mm wrench to remove the nuts because they are in a tight place.

    After the 1 bold and 3 nuts are removed, the entire headlight assemble will pull straight out. You don't need to take the headlight bulb out because there should be enough wire to pull out the assembly far enough to get to the turn signal bulb. This will allow you to change the turn signal bulb which should be a 4157 amber bulb.

    When putting the headlight assemble back in the van, there is a plastic pin in headlight assembly that goes into a hole in the front fender for alightment. Don't force the light. Take your time and the headlight assembly will go back in the van smoothly.

    Mar 17, 2009 | 1999 Plymouth Voyager

    1 Answer

    How do you access the right front turn signal bulb on a 2006 Pontiac Montana? HELP...it looks like there is no access to it. Thanks


    if their is a engine cover take cover off / their are 2 bolts for the headlight take them out and pull the headlight forward

    Jan 25, 2009 | 2006 Pontiac Montana

    1 Answer

    Replace ford escape turn signal front 2005


    you should not have t remove the headlight assembly to replace the bulb access should be under the hood. as for the moisture the bulb holder may be damaged or not fitted properly

    Oct 16, 2008 | 2005 Ford Escape

    Not finding what you are looking for?
    2006 Pontiac Montana SV6 Logo

    Related Topics:

    816 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    75077 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7768 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...