Question about Hyundai Tucson

Open Question

Ball joint replacement 2006 hyundai tucson - Tucson Hyundai Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
shawnsz
  • 64 Answers

SOURCE: lower ball joint replacement 2003 GMC Sierra 2WD

You have to drill them out, it can be a real pain to.

Posted on Feb 19, 2009

Ad
chrisK1997
  • 103 Answers

SOURCE: 2000 lincoln ls bad ball joints! should i replace whole knuckle or just ball joints

yes you can buy just the ball joints

Posted on Apr 18, 2009

  • 218 Answers

SOURCE: Replacing ball joints on 1999 Ford Expedition

U CAN REPLACE JUST THE BALL JOINT OR THEY COME WITH THE ARMS.DEPENDING ON MECHANICAL ABILITY AND TOOLS IT IS MUCH SIMPLER TO REPLACE THE ARMS

Posted on May 06, 2009

  • 753 Answers

SOURCE: replace upper ball joint 2003 silverado 1500

The ball joints on both 2wd and 4wd upper are pressed in you need to remove snap ring and using a hammer pop out the old one out this is after you seperate the upper arm from the spindle. To install the new ball joint you should use a ball joint press that you can rent at most autoparts shops

Posted on Aug 09, 2009

c17hydro
  • 2984 Answers

SOURCE: 2006 Hyundai Tucson spark plug replacement. How do

unbolt all the fastners on the corners and sides.

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the thermostat on a 2006 hyundai tucson?


Big black tube from your engine, to your radiator.... close to the engine. The thermostat is going to look like an ovular coupling with two bolts 180 degrees from each other. Very easy and inexpensive to replace.

Sep 03, 2014 | 2006 Hyundai Tucson

1 Answer

94 grand voyager how to remove lower ball joint. will i damage seal? I am replacing axle but not ball joint. I will use ball joint removal tool


That's the right way and only way to do this, just put some lube on the fork side, that will slide on the ball joint boot when removing joint.

Jul 12, 2010 | 2006 Hyundai Santa Fe

1 Answer

I have an automatic gas 2006 hyundai tucson. recently i noticed that when i engage the drive or reverse gear the vehicle lurches forward or backward accompanied by a banging noise. i have had both engine...


idle air control valve or iac same thing it controls idle speed yours is to high or you have a bad cv joint but i dnt think its that to new of car i would say your idle is to high

Apr 04, 2010 | 2006 Hyundai Tucson

2 Answers

Should ball joints on a 2006 Hyundai Azera of less then 14,000 miles need to be changed?


no it should not, you have deeper issues with with the front end. the worn ball joints are just the end result.

Oct 16, 2009 | 2006 Hyundai Azera

1 Answer

1999 hyundai sonata


raise the front end and support with stands, remove wheel, remove axle nut, remove bolt that attaches bottome of strut to control arm remove lower ball joint bolt smack the knuckle where the ball joint is to remove and flip the knuckle out of the way, use pry bar to pop halfshaft out of tranny. while installing new one make sure the splines line up and it pops in place installation reverse of removal

Apr 11, 2009 | 2006 Hyundai Sonata

1 Answer

Hyundai Tucson 2.0L Year 2006


Get the mechanic to check the front CV boots for tears and get them to check the front CV joints. Explain the problem to the service manager. They should know how to properly check them. The shafts usually come as a rebuilt assembly with new joints on both ends, and are relatively easy to replace.

Aug 26, 2008 | 2006 Hyundai Tucson

1 Answer

Hyundai Tucson 2.0L Year 2006


Sounds like bad CV (constant velocity) joints in the front half shafts.

They make the most noise at a full wheel cut.

Aug 06, 2008 | 2006 Hyundai Tucson

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...