Question about Ford Bronco II

1 Answer

What Size Torque Wrench Would I Use To Take Off The Heads? Thank You

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 8,215 Answers

Use a 1/2 inch breaker bar and 6 point socket.

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need the torque setting for auto lite spark plugs going into a 2005 ford taurus


My info says 11 ft lbs--motorcraft. That would probably work just fine for auto lite. I usually just snug-em up, no torque wrench. Sometimes it's awkward trying to get torque wrench and whatever applicable fittings in close spaces. If you can get a torque wrench in there, so much the better.

Nov 05, 2016 | 2005 Ford Taurus

1 Answer

Do I need a 36 in torque wrench extension to


You should not need a torque wrench to loosen/remove fasteners

Oct 05, 2014 | Cars & Trucks

1 Answer

Torque specifications


You have the wrong size Torque Wrench. IF you Torque Wrench measures nm, and it max'd out @ 130, you need a larger Torque Wrench. Convert nm to Ft. Lb and use these if necessary.

Sep 06, 2014 | Cars & Trucks

2 Answers

Citreon xsara 1999 1.8 16 valve cylinder head torque settings


If yours is an Xu series engine, you need to use a torque wrench and an angle dial wrench. Tightening is in 3 stages.
  • Stage 1: Tighten up to 60Nm (44 lb/ft) then fully loosen
  • Stage 2: Tighten up to 20Nm (15lb/ft) change to angle dial wrench
  • Stage 3: Angle tighten to 300 deg.
To avoid confusion, do stage 3 in 3 steps, tighten 100 deg each round and repeating the cycle until 3 rounds.

07718717-6a90-48f5-a87c-bc1ff81d67bd.jpg

04a9b611-4f0b-4da6-9052-a1cb2e517c02.jpg

Jun 13, 2014 | 1998 Citroen Xsara 1.6

1 Answer

Torque specification


Apply a light coat of engine oil on the threads and
under the heads of the cylinder head bolts.
- Install the plate washer to each cylinder head
bolt.
- Using Torque wrench, install and uniformly tighten the ten
cylinder head bolts in several passes.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)

Jan 26, 2014 | 1993 Toyota Corolla

1 Answer

I need to know how to find/set timing marks for 2002 Kia Sedona and head bolt torque specs


The head bolt torque on a 2002 Kia Optima is 45 ft/lbs of torque. Always make sure you use a good torque wrench to get it right. ------------------------------------------------------------------------------------
Original Launch X431 Master

Mar 13, 2013 | Cars & Trucks

1 Answer

HEAD TORQUE AND SPECS FOR A 2001 HONDA ACCORD 2.3L


Tighten the cylinder head bolts. Tighten the cylinder head bolts is sequence to 29 Nm (3.0 kgf-m, 22 ft. lbs.). Use a beam-type torque wrench. When using a preset type torque wrench, be sure to tighten slowly and do not overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt and retighten it. Make sure the threads are clean, new heads bolts are best.

10_29_2012_10_15_36_pm.gif

Oct 29, 2012 | 2001 Honda Accord

1 Answer

Im having to change my head gasket, whats the torque spec and sequence on a 96 landrover discovery? im changing both head gaskets. anything i should know?


start in middle and work outwards alternately ,bolt torque 80lbs and pull down if three passes ,speed key --rachet- torque wrench .although iam posting this i never use a torque wrench i go by the feel of the bolt stretching ,make sure heads have been checked and skimmed before refitting

Aug 10, 2010 | 1997 Land Rover Discovery

1 Answer

Torque specs on headbolts 95 taurus 3.8 litre and sequence


cast iron heads ,about 85lbs alloy heads 70lbs ,sequence start in middle and then one bolt to left and then one bolt to right ,just keep going left to right tightening them and you cannot go wrong ,pull down with a rachet first then a nice snap on bar ,i never use a torque wrench i feel the stretch on the bolts ,but thats me so use a torque wrench

Mar 18, 2010 | 1995 Ford Taurus

1 Answer

Replacing front wheel barings on a 2005 chev silverado. need torque specs for 3 mounting bolts and torque spec for shaft nut through center of bearing (spline gear)


the big one tighten with a big bar and pull it to about 120lbs ,the three smaller ones which i cannot place at the moment but if they are 17mm size heads then about 60 but i always feel them as i do them and never use a torque wrench or a air wrench ,just muscle and 40yrs of feel

Mar 02, 2010 | 2005 Chevrolet Equinox

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...