Question about Toyota Pickup

1 Answer

Changed rear brake lines now cant bleed wont hold on 1995 toyota pick-up

Posted by on

  • 1 more comment 
  • frinzielectr Oct 05, 2010

    after bleeding brakes and getting all fluid out of them the pedal still goes to the floor. no pressure.

  • frinzielectr Oct 05, 2010

    after bleeding brakes and getting fluid out of all of them brake pedal still goes to floor. wont hold pressure. this all happened after we changed 2 rear brake lines. have changed master cyclinder since but didnt help

  • frinzielectr Oct 06, 2010

    will try this and respond back.



    thanks

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,299 Answers

Not real sure what you mean by won't hold on. Can you explain?

Posted on Oct 05, 2010

  • Rodney Clark
    Rodney Clark Oct 05, 2010

    Thanks for the clarification. Now that you have the lines bled and it will still not hold pressure. That means that there is a line or a wheel cylinder or caliper leaking somewhere. The pressure has to be going somewhere. I would start at the places where the new lines are installed. Make sure that you are using a tubing wrench. You should have brake fluid leaking from somewhere.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bleed rear brakes on a 1995 saturn


same as bleeding any brake system . 2 person operation. pump up the brake pedal and hold it down -undo the bleed screw until the pedal is on the floor. hold there until the bleed screw is tightened . repeat the process until no air comes out of the bleed screw. Always start at the longest line first and finish at the shortest. Keep an eye on the reservoir level during the process.

Aug 12, 2014 | Cars & Trucks

1 Answer

Brake and e brake warning lights stay on happen when i blew a brake line.


If brakes are mushy then you still have air in the lines.Did you bleed all 4 wheels?have wife push brake pedal down once and hold then bleed hold down one and bleed and so on if this has a quick takeup master cylinder pumping 3 or 4 times then bleed wont work

Jun 14, 2012 | Chevrolet Cars & Trucks

1 Answer

How to replace rear shocks on a 86 Toyota celica gts?


This procedure can be found at autozone.com. You can register for free, listing make, model, year, and engine size. Find procedure under "repair guides". Good illustrations, too.
1. On liftback, remove rear speaker grilles. On coupe, remove suspension service hole cover or the speaker board (on rear deck by back window).

2Drum brakes or disc brakes? No matter: Do not break apart the brake lines. There is a clip on the strut to hold the brake line and it's connection to the rubber brake hose. Take the c-clip off and cut the brake line retainer with a hacksaw (careful of the brake line and hose). This way you won't have to worry about bleeding the brakes when done. Take the line out of the strut retainerclip. When re-installing, just use a zip tie to hod the brake line secure.
3. Loosen, but don't remove, the 19mm nut holding the suspension support to the strut (this is the larger center nut on top of strut at the deck by rear window.
4. Disconnect stabilizer bar at lower end of strut housing. You will need a 14mm wrench and a 3/16 (or equivalent metric size) allen wrench to hold the link steady while removing the nut.
5. Disconnect strut at the axle carrier-17mm size bolts.
6. At top, remove the three strut to body nuts-size 13mm., and remove the strut.
To put your new struts inside the coil spring, you will have to have a spring compressor. I don't have one, so after removing strut, took to a shop for that, cost was $20 for one side. Picked it up and installed it myself.
To install: Position assembly and tighten the upper strut to body nuts to 23 ft. lbs.
2. Tighten lower strut-to-carrier bolts to 119 ft. lbs..
3. Connect stabilizer bar to strut. Tighten the nut to 26 ft. lbs.
4. Tighten top strut holding nut to 36 ft. lbs. (the shop had already done this for me) and install dust cover.
5. Reconnect brake line and hose, and bleed the brakes, if you broke the line apart. If you didn't break the line apart and just cut the clip retainer, you will not have to bleed the brakes.
6. Lower the car and have rear wheel alignment checked.

If you have a spring compressor, and can do that procedure yourself, the instructions for it are found at autozone.com, along with the above that I have outlined.

Jun 03, 2012 | 1986 Toyota Celica

1 Answer

Brakes wont bleed


Sounds like you need to change your Master Cylinder . This is the cylinder located below where the brake fluid goes. You stated no pressure and this is a symptom of this cylinder plunger going bad and not pushing fluid threw the lines. Remember to rate my solution

May 01, 2012 | 1995 Mitsubishi Diamante

1 Answer

Have an 89 festiva changed 5 master cylinders and still cant bleed front driver and rear pass wheel and also changed distribution block 3 times. i cant bleed it rite from the front port of the master...


Section 06-06: Hydraulic Brake System 1992 Festiva Workshop Manual GENERAL SERVICE OPERATIONS Manual Bleeding
  1. Read Hydraulic System Bleeding General Information.
  1. Clean all dirt from the master cylinder filler cap.
  1. Fill the master cylinder with the specified brake fluid. During the bleeding operation do not allow the master cylinder to run dry.
  1. If the master cylinder is known or suspected to contain air it must be bled before the wheel cylinders or calipers. To bleed the master cylinder, loosen the front line fitting and have an assistant push the brake pedal slowly through its full travel. While the assistant holds the pedal, tighten the brake line fitting. After the line fitting is tightened, the assistant may release the brake pedal. Repeat this procedure on the rear brake line. Repeat the entire process several times to ensure all air has been removed from the master cylinder.
  1. Remove the bleeder screw cap from the appropriate rear wheel cylinder.
  1. Position a box end wrench on the bleeder fitting.
  1. Attach a rubber hose to the bleeder fitting. The hose has to fit snugly around the bleeder fitting.
  1. Submerge the free end of the hose in a container partially filled with brake fluid.
  1. Loosen the bleeder fitting approximately three quarters of a turn.
  1. Have an assistant push the brake pedal slowly through its full travel and hold it there.
  1. Close the bleeder fitting.
  1. Have the assistant release the brake pedal.
  1. Repeat Steps 9 through 12 until air bubbles cease to appear at the submerged end of the bleeder hose.
  1. When the fluid entering the bottle is completely free of bubbles, tighten the bleeder screw, remove the bleeder hose, and install the bleeder screw cap.
  1. Repeat Steps 5 through 14 at the appropriate diagonal front caliper.
  1. Check the master cylinder fluid level. If necessary fill it to the correct level with the specified brake fluid.
  1. Check pedal feel. If the pedal remains spongy, repeat the bleeding process or, if necessary, refer to Diagnosis and Testing in Section 06-00.

Jan 04, 2011 | 1991 Ford Festiva

1 Answer

95 Avalon rear brake caliper replacement


get a hayes repair manul from the auto parts store that will tell you every thing youneed to know

Aug 11, 2009 | 1995 Toyota Avalon

1 Answer

Toyota yaris brakes how do you bleed the brakes on a toyota yaris


have someone pump the pedal and hold it, then you work from the right rear, left rear, right front, left front, while the person pumps and holds several times at each wheel.

Jun 10, 2009 | 2007 Toyota Yaris

2 Answers

Cant bleed out brakes


It takes time, do you know the sequence to bleed the brakes? Most cars r different. And you have to keep pouring brake fluid, That is a two person job. Make sure all lines r connected to MC and not leaking. After a while if nothing comes out MC could be diffective.

Jun 06, 2009 | 1990 Toyota 4Runner

1 Answer

Replacing rear brake calipers...


Hi there.

Jack the rear end of the car up making sure the hand brake is off, disconnect the brake lines to the rear making sure u have clampted them with a clamping tool *set of mole grips if all you have*

start dismantle the calipers *follow the bolts holding the caliper to the suspension leg*

after you have re-fitted the calipers and brake bads re connect the brake lines and bleed the system to make sure and be safe. thanks alot Lee.

Apr 10, 2009 | 1993 Toyota MR2

2 Answers

Changed break line but still have no pressure in breaks


to do a complete job. you need to bleed all 4 wheels, starting from Right Rear. Right front. Left Rear. Left Front.

Apr 07, 2009 | 1995 Chevrolet Silverado 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...