Question about Ford F-350

1 Answer

How would i get the code for the engin light beeing on

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 153 Answers

You will have to get your car plugged in to a fault code reader, they will attatch to your OBD plug and rear your fault codes from there. Once codes have been cleared and fault diagnosed the light will be extinguished

Posted on Oct 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hi i put new spark plug wires in now my engen light is on what can bee the problem

I dont know. Have the codes pulled and post the code on here.

Sep 11, 2017 | Cars & Trucks

1 Answer

My check engine light on my 2000 honda prelude sh shows atts

in the USA, our cars are OBD2 , (you there?)
and all scan tools can scan this car. an $9 tool (fleabay)
scan it .
or get it scanned, then post the DTC codes. all of them.
if its EVAP , code, tighten the gas cap, reset the PCM (same tool)
and that is not corrected.
you can get the zone to scan it but they 1/2 the time miss them all
and miss factory codes.
buy the tool, or go to any USA ASE certified, shop. and its bees-knees.

Nov 22, 2013 | 2000 Honda Prelude

1 Answer

Trouble codes

yes it can. some times codes show up with no light

Feb 09, 2013 | 1997 Pontiac Grand Am

1 Answer

Have 95 Nissan Maxima that stalls at stop lights and when slowing down. Have seen several solutions to problem: Mass Air Flow, idle Air flow valve, crack in intake boot and engine coolant temp sensor. How...

unfortunately in your mode maxima nissan had quite a few issues because of beeing the first model of A32 body style from the older J30 model maxima. from what i have seen in the past it could be anything from bad harness, to flodded ECM/computer because of water entering into vehicle because of faulty cowling on top of windshield, to bad ground between trans and engine housing. if the check engine light is on, you need to scan for codes to get started. if no check engine light is on that that makes it alot harder to diagniose. if no check engine light is on, i would look at the top of the computer bracket to see if its rusted up, that coilud be sign of water coming in and flodding computer causing running issues/drivability porblems.

Aug 19, 2011 | 1995 Nissan Maxima

1 Answer

My Chev. Trail Blazer 2002 six cyl. has been workinf great until a month ago when Engin light came ON and stayed ON. When running at normal sspeds you feel very little of Vibration/hestation , but when at...

best you can do is have a real ime scanner hooked up to it with snapshot capabilities, that way yu can monitor all sensors and actuators, code scanning doesn't tell you enoough

Nov 22, 2010 | 2002 Chevrolet TrailBlazer

2 Answers

Electrical problems bmw 1999 318i

these system all have a common control module, so the lights are related to a single part failure, since parts cost a tidy amount of cash for this car have the dealer use there special scanner and see what trouble code is stored for the problem, whenever the lights are on there will be a trouble code stored by the control module.

Aug 13, 2009 | 1999 BMW 318 ti

3 Answers

Engine sputtering, engine skips at low speeds, emission light on

Is the service engine light on? If so, check with you local auto parts store....most will scan the code free or loan you a scanner in their parking lot.

Jun 29, 2009 | 2005 Ford F-150

1 Answer

Service engine soon, electical displays? the alternater has bee replaced and the battery..

what do you mean it , shows electrical?

The light on just means you are not passing emissions. not a big deal unless it's flashing.
Go to Autozone, they will scan test for codes for free.

May 21, 2009 | 1996 Cadillac Seville CA Value

2 Answers

I have a toyota 4-runner and my maint light is on Does this mean I need service

most likely requires a service make sure engine oil/air/fuel filters are changed when beeing serviced check charging rate,aux belts etc reset light

Feb 19, 2009 | 2008 Toyota 4Runner

1 Answer

Engine Light does't come car will not start

did you get the codes by doing the "key dance"(on,off,on,off,on) ?

if so, it almost always flashes a 12 and 55. here is what they mean.

12 - direct power input to the PCM has been disconnected within the last 50 key-on cycles

55 - End of error messages

Dec 13, 2008 | 1995 Eagle Talon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5677 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides