Question about 2006 Cadillac CTS

1 Answer

How do you access right front turn signal blub

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 516 Answers

I removed the entire head light assy first. There are two thumb screws to do this. This gives adequate access to the turn signal bulb. Hope this works for you.

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I turn my turn signal on I can hear the turn signal but turn signal don't work


If on the dash the arrow just lights but no blink. You have a blown light bulb on that side could be front or rear. Turn on flashers it should ID which blub
mike

Feb 19, 2016 | 2003 Ford Focus

1 Answer

Passenger side turn signal flashes faster but dont work even at day runing light, comes on when head lights are on, replace bulb and socket because was melted but stilldoes the same


Turn Signal Lamps
The turn signal lamps may only be activated with the ignition switch in RUN or BULB TEST position. The T/SIG fuse supplies ignition voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, the turn signal switch sends an ignition voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. When the turn signal switch receives the on-off signal it will send that signal to the following lamps on the LH or RH side:
?€¢
The Rear Turn Lamp


?€¢
The Turn Signal Indicator


?€¢
The Sidemarker Lamp


?€¢
The Sideview Mirror (Pontiac Thunder only)

The turn signal switch also sends a separate on-off signal to the Daytime Running Lamps (DRL) control module, which relays the signal to the appropriate front turn signal. The front turn signals are grounded at G101 and G102. The rear turn signals are grounded at G401. The sidemarker lamps are grounded through the corresponding front parklamp.
The sideview mirror turn signals are a bank of LEDs placed behind the mirror glass.
The hazard lamps operate on battery voltage. The HAZARD fuse supplies battery voltage to the turn signal switch. When the hazard switch is pressed, the turn signal switch sends battery voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. The turn signal switch send the on-off signal to all the turn signal lamps, causing all the lamps to flash including both IPC turn signal indicators. The hazard lamp/turn signal flasher is grounded at G200.
When the parklamps are ON, the sidemarker lamps receive voltage from the park lamp supply voltage circuit and illuminate. The sidemarker lamp is grounded through the corresponding rear turn signal. When the turn signal switch is place in the left or right hand position, the rear turn signal illuminates and the sidemarker lamp will loose its ground, causing the sidemarker lamp to turn off when the turn signals are on and to illuminate again when the turn signal is off.
Which blub an socket did you replace ? check the other blub ? The switch and or the flasher module can cause this problem .
Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?

Which

Oct 11, 2015 | 2001 Pontiac Montana

1 Answer

Right turn signal does not blink bulbs are good housings are good need help


mcdevito75 here, Double check both the front and rear blubs, also make sure front and rear bulb sockets are firmly inplace on the car.

Jun 18, 2010 | 2001 Ford Escort ZX2

1 Answer

Front passenger side turn signal blub only last about 3 months before going out.what could be the problem


Are you sure you replaced it with the correct bulb?also look at the connector and see if it looks burnt.If it does then replace it and when you replace the bulb add die electric grease to the contacts.This will keep the heat down.Good luck and I hope this helps.

May 10, 2010 | 2004 Cadillac SRX

1 Answer

Left flasher dead, right on works


double check your bulbs again, if still good
check your flasher

G

May 09, 2009 | 2005 Jeep Wrangler

2 Answers

Front turn-signal bulb burned out.


It is a tight squeeze, but you can get your arm down past the headlight to the brake cooling duct and pull the brakeduct off the nose of the car back and to the side. Then you can reach through that hole and replace the turn signal blub

Jun 13, 2008 | 2001 Chevrolet Corvette

Not finding what you are looking for?
2006 Cadillac CTS Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...