Question about 2004 Ford F150

1 Answer

I have a 2006 F150, just last week the heater switch that controls speed from 1-4 started giving trouble, first it stopped working on 1, then a few days later, 2 stopped, then 3 and now all I have is high #4, could this be the resister and not the switch itself and if so, where is the resister located so I can replace it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 8,587 Answers

Your truck uses a speed controller rather than a resistor. You will probably have to replace the controller.I have a 2006 F150, - b7ba8b9.gif

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Which fuse controls the cruise control? If not the fuse what else could cause the problem?


the IPM -- refers to the integrated power module under hood (fuse box) Fuse #36




25661612-sinuhqnwkyunxx3smtti0pjv-1-0.gif

Apr 23, 2015 | 2006 Dodge Dakota

1 Answer

Cruise control won.t work on 2002 King Ranch F150 not cable and not fuse .. how do I take steering wheel apart without blowing air bag


Did you have the recall done ?
recall 05S28. Description: Speed Control Deactivation Switch.

Is this the fuse you are talking about ( the recall harness has an inline fuse in it ) ?
- If it is, how did you test this ?

Did you run the CC self test ?
Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

- 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

- 3 flashes - deactivator switch is open or circuit defective.

- 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Please post back the answers as a comment to this problem.

Thanks

Oct 30, 2010 | 2002 Ford F150 Regular Cab

1 Answer

Which fuse is for cruise control in 2003 ford f150


The fuses for the speed control from the factory are :
Engine Compartment fuse panel #7,
Cab fuse panel Fuses #15, #13, #5

The fuse that goes to the recall part is Fuse #13, 20A

The recall is 05S28. Description: Speed Control Deactivation Switch.
The part number for the recall is : 1L1Z-9F924-AA
The part has a fuse inline that is marked as non serviceable, but 1 revision I saw, it was just an ATM fuse under tape. Not sure if this is the final revision that was used on your truck ( or should have been used ).


The self test for the Cruise Control ( for 00-03 MY, with the CC light on the cluster ) :

With the key off depress and hold the cruise control off button while turning the ignition to the run position,don't start the truck, the cruise light will flash once to let you know it is in self test.
Five additional flashes indicate a bad cruise control servo

Release the cruise off switch and within 5 seconds depress the other switches in sequence:
1. on
2. resume
3. coast
4. set/ accel
The speed control light will flash as each switch is depressed.

If the last one does not flash it may then flash a code

After this the cruise will move the throttle to test the actuator and the cable.
Make sure the throttle returns to idle and turn the key off.
----------------------

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

- 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

- 3 flashes - deactivator switch is open or circuit defective.

- 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Oct 19, 2010 | 2003 Ford F150 Regular Cab

1 Answer

My speed control dont work fuse ok


Is the Recall done ? recall 05S28. Description: Speed Control Deactivation Switch.

You can try the speed control self test
Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

- 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

- 3 flashes - deactivator switch is open or circuit defective.

- 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Aug 19, 2010 | 2003 Ford F150 Regular Cab

2 Answers

2002 Ford F150. Cruise control stopped working.


Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be a blow fuse in the recall harness, if you did have it done.

Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

Feb 22, 2010 | 2002 Ford F150 Regular Cab

1 Answer

The crise on my 2002 F150 stopped working. Occasionally the cruise light will flash when I try to set, but it still won't work. Also, I have had the recall work done, and this problem started after that.


Could be the fuse in the new harness is blown.

Try the CC self test, to see what the flash code returned is :

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

— 3 flashes - deactivator switch is open or circuit defective.

— 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Nov 29, 2009 | 2002 Ford F150 Regular Cab

1 Answer

2001 F150 6 cyl. Cruise control just quit working today. I turn it on and hit set, cruise light flashes and does not stay on. Please Help. M Mitchell


2 things

1. Is your truck in the list for the recall, or did you have it done ?
recall 05S28. Description: Speed Control Deactivation Switch.

2. Run the Cruise Control Self test
Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

— 3 flashes - deactivator switch is open or circuit defective.

— 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Oct 22, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

2004 Ford F150 - AC/Heater blower speed 1 & 2 not working.


You might have a bad speed selector switch, or your blower motor resistor is faulty.

Mar 17, 2009 | 2004 Ford F150

1 Answer

Heater fan switch runs on #5 speed only, 2000 Chevy Malibu


you need a blower motor controller. call your local bmw dealer thay will know what you are talking about cause thay have had trouble with this. i think thay offer a updated part.

Feb 25, 2009 | 2002 BMW 5 Series

Not finding what you are looking for?
2004 Ford F150 Logo

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...