Question about Ford Ranger

Open Question

Need diagram of 86 ford ranger manual transmission E67A-7003-BD with build code132267 im replacing the synchronizers

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 10 Answers

SOURCE: have a 86 ford ranger 2.3 l 4cy in mornings

its your fule filter theres 2 of them i the 86 ford ranger you need to change them the location of the fule filters are on google just tipe in fule filter 1986 ford ranger location it should pop up there about 8 dollors a peace easy fix and your truck is like new also get a new battey if you havent k have a good day. oh i know this because i own one had the same problem

Posted on Jun 13, 2009

Ad
PyroPCMan
  • 405 Answers

SOURCE: 1991 Ford Ranger manual transmission remove

444a343.jpg

  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever assembly from the control housing.
  3. Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
  4. Raise the vehicle and support it safely.
  5. On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
  6. Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
  7. Disconnect the speedometer from the transfer case/extension housing.
  8. Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
  9. Place a wood block on a service jack and position the jack under the engine oil pan.
  10. On 4WD vehicles, remove the transfer case from the vehicle.
  11. Remove the starter motor.
  12. Position a transmission jack, under the transmission.
  13. Remove the transmission-to-engine retaining bolts and washers.
  14. Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
  15. Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
  16. Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
  17. Lower the transmission jack and remove the transmission from the vehicle.
To install:
  1. Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
  2. Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
  3. Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
  4. Install the starter motor. Tighten the attaching nuts.
  5. Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
  6. On 4WD vehicles, install the transfer case.
  7. On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
  8. Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
  9. Connect the hydraulic clutch line and bleed the system.
  10. Install the speedometer cable.
  11. Check and adjust the fluid level.
  12. Lower the vehicle.
  13. Install the gearshift lever assembly. Install the boot cover and bolts.
  14. Reconnect the negative battery cable.
  15. Check for proper shifting and operation of the transmission.
The above was pulled frrom:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800391da

hope this helps

Posted on Jul 02, 2008

SOURCE: 86 ford ranger

its under the carpet on the passanger side at the firewall

Posted on Jul 21, 2008

SOURCE: i need a 2002 ford ranger fuse box diagram and afuel pump relay switch diagram

Hi

go to www.motorcraftservice.com then click on the owner guide and put in your truck information
then choose the 1st owner manual printing and should be between page # 184 to 200.

Good luck and I hope this will awnser your question.

Posted on Nov 08, 2008

johnny5846
  • 379 Answers

SOURCE: firing order diagram for 1986 ford ranger

you will find this site usefull , here is the diagram for 1986 ford ranger 2wd 2.9liter v6 firing order .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm


Fix Ya vote is my Reward , thanks .

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a 86 Ford ranger spark plug diagram


https://www.google.com/search?q=86+ford+ranger+spark+plug+diagram&tbm=isch&imgil=ChAyBXLWz1uEmM%253A%253B6p7Wh6PGke8PMM%253Bhttp%25253A%25252F%25252Fwww.therangerstation.com%25252Ftech_library%25252F2_9_Page.html&source=iu&pf=m&fir=ChAyBXLWz1uEmM%253A%252C6p7Wh6PGke8PMM%252C_&usg=__ZS-6FtD-mg1urpuXuWpFu1C0x7w%3D&biw=1024&bih=638&ved=0ahUKEwiXtpyvrI7TAhWj6oMKHTdjAugQyjcIOQ&ei=OW3lWNe1MKPVjwS3xonADg#imgrc=ChAyBXLWz1uEmM:

Apr 05, 2017 | Ford Cars & Trucks

1 Answer

My 1988 Ford Ranger with 5 speed transmission has a locked synchronizer ring. Can the rings be seperated, if so how and will it still work?


The rings are locked because they are worn excessively and you can pry them apart but the next time you shift they will lock together again. sorry but you need to buy and replace parts

Nov 01, 2015 | 1988 Ford Ranger

1 Answer

Free wiring schematics


To Whom It May Concern,

Enclosed is a link to a .pdf formatted 2007 PJ Ranger Wiring Diagrams Manual. Perhaps this can steer you in the right direction. http://the.internetissrs.biz/ranger/Volume%203/Wiring%20Diagrams/Wiring%20Diagrams%20Manual.pdf

Jun 20, 2014 | 2007 Ford Ranger FX4 Off-Road

1 Answer

I have a 1991 Ford Ranger 3.0, 6 cyl w/manual transmission. When shifting it's not going into gear easily and some times not at all. Any suggestions?


1. Your clutch may be worn or out of adjustment.
2. If it is a hydraulically activated clutch it may be low on fluid.
3. Possibly the synchronizers in the transmission are worn out.

Apr 16, 2011 | 1991 Ford Ranger Supercab

2 Answers

Will a 87 ford ranger v6 4 wheel drive trans. fit in a 86 ford ranger 4 cyl 4 wheel drive


If automatic transmission wont work engine block's are not the same, if stander transmission you could swap out bell housing held on with four bolt's from one to the other. Good luck and hope this was very helpful.

May 19, 2010 | 1986 Ford Ranger 2WD

1 Answer

My 1996 ford ranger has to be forced into 1st and 2nd gears. its a manual transmission. what would cause this?


Sounds like the clutch is going or the slave or master cylinder is failing. You could have some bad gear synchronizers.

May 02, 2010 | 1996 Ford Ranger SuperCab

1 Answer

Need avacuum diagram for a1980 258 6 cylinder out of a jeep wrangler where do i look or find this


1980-86 6-258 with manual transmission, except California

6cdc854.jpg



1980-86 California 6-258 with automatic transmission

4a41de8.jpg



1980-86 California 6-258 with manual transmission

3d98dc4.jpg



1980-86 Canadian 6-258 with automatic or manual transmission

73a3723.jpg


Hope this help (remember rated and comment this).

Mar 25, 2010 | 1989 Jeep Wrangler

4 Answers

Ford ranger, getting harder to shift into gear


Suggest you check the fluid level of the transmission first. Remove the fill plug, and see if it is Below the proper level. Do Not fill at this time! There is a reason for this.

Then I would suggest draining the fluid. You are also looking for brass fragments in the fluid. Drain into a three quart metal, or plastic drain pan. (They are approximately 18 inches across, and 4 inches deep)

1.Manual transmissions use Synchronizer's made of a brass alloy. The synchronizers have tapered teeth, that the nose of the teeth can be worn down. Also a tapered surface on the synchronizer, that can be worn down. Brass fragments in the transmission fluid is a sign of this wear.

Some brass 'dust' will occur as normal wear. A large accumulation means you have problems. Transmission is hard to shift, is one of those symptoms due to this.

This link to an animated working of a five-speed manual transmission, may help to explain how the components interact with each other, and also help me to explain the Synchronizer/s.
(From Howstuffworks.com - Auto- Under the Hood - Transmissions and Drivetrain)

http://auto.howstuffworks.com/transmission3.htm

Looking at the animation, observe the 'gold' colored parts. In particular, observe the the pair of gold colored teeth at the rear. (The teeth are in a vertical row, going up and down)

Now also observe the blue colored teeth next to them, on either side. (On the spinning gears)
You are looking at a side view of the transmission, and also a side view of the Synchronizers.

The synchronizers are round just like the gears. They have a Female tapered surface where they meet the gear. The gear has a Male tapered surface on the outside of the gear, that matches.

When the female tapered surface of the synchronizer meets the male tapered surface of the gear, the friction contact makes the synchronizer start turning the same speed, as the gear.

Helps the gear being shifted into start turning also, and the - teeth of the synchronizer, - gear to be engaged, and - already turning components are synchronized to each other. They will be all turning the same speed, so shifting will be smooth.

This shows you Synchronizer rings for a 4-speed Muncie transmission,

http://cgi.ebay.com/ebaymotors/MUNCIE-4-SPEED-BRASS-SYNCHRONIZER-RINGS-1963-TO-1974_W0QQitemZ360137693405QQcmdZViewItem?rvr_id=&itemid=360137693405

Enlarge it for a better view.
See the teeth going around the synchronizer ring? Notice that they are pointed, or V shaped. When the nose, or tip of this V is worn down, a manual transmission is hard to shift.

Also observe the flat landing on top. (In this view it's on top) The flat landing has three rectangular cutouts in it. (There are used for Detents)

Come from that top landing, down the side to the teeth. This Side has a tapered surface. Tapered ever so slightly, that it is not readily visible in this photo.
When this tapered surface wears down, the transmission is hard to shift.

Summation?
1.Low fluid will cause hard shifting. It will also cause abnormally high wear of the synchronizer rings, (Synchronizer Rings are also referred to as 'Blocker Rings')

2.Worn Synchronizer Rings,
Broken or worn Detent 'buttons',
Broken Detent Springs,
and worn Synchronizer Hub's,
will cause hard shifting.

Should you not have an abnormal amount of brass shavings in your transmission fluid, and found the fluid to be low, you may want to just replace the fluid to the proper level, and see if this works first.

If so, I suggest contacting your Ford dealer, and see what the proper transmission fluid is for YOUR Ford Ranger. They will go by THE transmission is used in your truck, and will have any updates if better fluid has been developed since your truck was made.

I know dealers are expensive to buy from sometimes, but I implore you to use the transmission fluid they recommend.
It will have special additives.



Oct 31, 2009 | 2004 Ford Ranger

1 Answer

2003 Ford Ranger Extended Can 3.0L V-6 Flex Fuel Automatic Transmission. I put a new motor in my little truck and now the transmission acts like its in neutral. I just found out the transmission is...


How do I change the 2003 Ford Ranger XLT 3.0 L Flex Fuel -Auto Trans 2wd Camshaft synchronizer and sensor . Do I need any special tools ? Are there after market parts that are precise replacements for the OEM parts ?

Aug 07, 2009 | Ford Ranger Cars & Trucks

1 Answer

I need a 2002 ford ranger fuse box diagram and afuel pump relay switch diagram


Hi

go to www.motorcraftservice.com then click on the owner guide and put in your truck information
then choose the 1st owner manual printing and should be between page # 184 to 200.

Good luck and I hope this will awnser your question.

Oct 27, 2008 | 2002 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...