Question about 1994 Buick Skylark

1 Answer

The master cylinder was changed/ blinkers are not working now, could this be a fuse or something disconnected from dealer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 8,161 Answers

No relationship between these 2 issues. Check the flasher unit under dash, driver side of steering column, mounted on support bracket

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal blinking fast. Why would it do this?


If the dash signal is blinking fast and the back of car signal is NOT working, then the problem is the bulb in the back of the car. The one that is not blinking needs to be replaced. The bulb that's not blinking is burned out, and this changes the resistance of the blinker circuit causing the blinker to flash rapidly on the dash indicator. FIX: Replace the burned out bulb in the back of the vehicle.

Note - Sometimes this situation causes the blinker module on the fuse panel to permanently change to a rapid or even a non-blinking state. In this case you must also replace the blinker device itself, which is on the fuse panel and looks like a small cylinder (or cube) less than one inch in diameter.
25872306-0gjnqcgakvlfffn2os0snv0o-4-2.jpg

25872306-0gjnqcgakvlfffn2os0snv0o-4-8.jpg

25872306-0gjnqcgakvlfffn2os0snv0o-4-3.png

Sep 19, 2015 | 2002 Toyota Camry

2 Answers

I seem to have a problem with my hydro breaking system.Found front worn out while the rear shoes were covered with oil and had not been working for some time.After replacing calipers,rotors,shoes and wheel...


ALL YOU CAN DO IS FLUSH WITH CLEAN FLUID PUMP AND BLEED NOTE: ALWAYS START FROM THE FURTHEST WHEEL FROM THE MASTER CYLINDER AND WORK YOU WAY BACK. SOME TIMES YOU CAN OPEN THE LINES WITH COMPRESSED AIR WHEN YOU DISCONNECT ALL THE LINES FROM THE CYLINDERS

Aug 15, 2009 | GMC Sierra 3500HD Cars & Trucks

2 Answers

96 Dodge Grand Caravan. blinkers not working


check the fuse and relay that control the blinkers, also check all bulbs make sure they are good

Jul 30, 2009 | 2000 Volkswagen Beetle

1 Answer

The left front blinker is out on my 1984 VW Rabbit Convertible (German Made.)  I replaced the bulb, still not working. I need to know which fuse to replace.


If the other blinker works it is not the fuse something is wrong with the socket for the blinker or a poor ground look at the filiment on the bulb I have had brand new bulbs blow out immediately after changing.

Jul 14, 2009 | 1984 Volkswagen Rabbit

1 Answer

Changing 4 calipers and there is no oil com out when try to bleed


The master cylinder supplies the pressure to the brake fluid that travels between the maste brake cylinder resevoir and the brake caliper pistons (through the brake lines. If the master cylinder fails there will be insufficient compression of the brake fluid to make the calipers operate as designed. Leaks in the brake lines and/or cylinders is a possibility, and unrelated to functionality of the master cylinder. Also, pistons located in the brake calipers can form a corrosion ring on their inside walls if there is breakdown in the brake fluid or moisture that gets into the lines. Operating the vehicle when there is insufficient brake fluid in the master cylinder resevoir can also lead to air getting into the brake lines, causing bad working brakes. Air compresses more than brake fluid, and the master cylinder isn't designed to compress air in the brake lines. Sounds like a bad case of "lack of maintenance", as opposed to bad advice from the mechanics. That said, there's no excuse for bad installation. But, it's tough to improperly install a brake line since they are nothing more than hollow metal tubes. There should be no rubber connectors installed in the brake lines. When bleeding the brake lines one must remove all of the trapped air before you will see any fluid appear. If the valves in the master cylinder are not properly operating the master cylinder will not allow the brake fluid to get into the brake lines.

Hope this helps.

Jun 13, 2009 | 1999 Volkswagen Passat

2 Answers

2001 chevrolet tahoe ABS Brakes light on when we are driving


This means...something needs to be attended to in your braking system! I'm sorry to be harsh, but the light comes on.....FOR A REASON! Have your brakes looked at, by a professional ASAP!....before you have a life changing accident.

Jun 01, 2009 | 2001 Chevrolet Tahoe

3 Answers

Dashboard and tail lights out on 97" Nissan Sentra


i would check the connectors under the dash they have a tendancy to get loose are get hot and short a fuse this is most likely the problem...please rate this....

Sep 01, 2008 | 1997 Nissan Sentra

1 Answer

Blinker problem


I would suggest an internally shorted multifunction switch. It should not be very expensive at a dealer and really easy to replace.
MULTI-FUNCTION SWITCH REMOVAL
  1. Disconnect battery negative cable.
  2. Remove the upper steering column cover. Refer to steering column cover removal procedures below.
  3. Remove multi-function switch mounting screws Multi-Function Switch
  4. Disconnect wire connectors. Lift the switch straight up to remove.
INSTALLATION For installation, reverse the above procedures.
  1. Tighten multi-function switch to column retaining screws to 2.3 N·m (20 in. lbs.) torque.
  2. Tighten steering column cover retaining screws to 2 N·m (17 in. lbs.) torque.

Jun 19, 2008 | 1998 Chrysler Sebring

Not finding what you are looking for?
1994 Buick Skylark Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...