Question about 2004 Audi A4

1 Answer

With an audi a4 to replace the front wheel bearing do i need a whole hub or just the bearing

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 153 Answers

You will need just the bearing, I'm sure this is just 1 unit but is 2 bearings housed in 1 casing, if that makes sense,

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

16885 vehicle speed implausible signal P0501 static No indication on display?


This means your VSS, vehicle speed sensor is not sending voltage to the computer. Speed sensors must maintain a specified gap between the magnet and the ring. It is possible that the magnet is dirty or the wire is damaged, or the plug is dirty or loose. If its none of the mentioned then a bad wheel bearing will cause your speed sensor to fail. To check if it's the wheel bearing, jack the front wheels off the ground. Make sure to block the rear tires to prevent it from rolling. Grab your front tire at the 12:00 and 6:00 positions and try as hard as you can to wiggle the tire. If your tire has any movement in and out, then you must replace your wheel bearings. The speed sensor is built into the hub.

Mar 10, 2016 | 1997 Audi A4

1 Answer

How to replace front right wheel bearing


Front wheel drive?if so which i think it is you need to remove the whole hub assy then use a universal hub seperator to remove the bearing then press a new bearing in. some vehicles such as ford festiva need a special tool to adjust a shim thickness which is imperative. I would sugest you get a 2nd hand hub assy with a good bearing in it & just replace the whole assy :-)

Oct 12, 2012 | 2000 Ford Windstar

1 Answer

How to remove front wheel bearing from audi a4 1.8


take the hub off take to garage and get them to press out old bearing and get them to put new one in

Jan 13, 2012 | 1996 Audi A4

1 Answer

Replace front wheel bearing


The front wheel bearing for your Impala is an integrated wheel hub/bearing/ABS.
The whole thing gets replaced. It should look like the one off my Bonneville; Bearing.

Remove wheel/tire. Remove brakes. Remove rotor. Remove axle nut. Press-out axle shaft*. Unplug ABS connector. Remove 3 bearing bolts.

*To press out axle, you may need a special tool from an auto parts store.
Don't forget to put the heat sheild back on during reassembly, and the axle nut need to be very tight.

zeevert_62.jpg


After Bearing/hub removed:
zeevert_73.jpg

Apr 21, 2011 | 2004 Chevrolet Impala

1 Answer

Bearing on front wheel


What about it? Most people question if you can just replace the bearing, or do you need to replace the whole hub assembly. Unfortunately, need to replace the whole wheel bearing hub assembly.

Dec 16, 2010 | 2004 Chevrolet TrailBlazer

3 Answers

Can I replace the front bearings myself or do I have to buy the whole hub.


Hello, the front wheel bearings are not a servicable part. you have to replace the front hub bearing assemblies. here is a picture.



mrtechwrench_14.gif

Dec 05, 2010 | 2004 GMC Envoy

1 Answer

How is front wheel bearing replaced on a 2001 Volvo S40?


most front wheel bearings are pressed in you half to take the whole control arm off pull out the hub press out the bearing grease the new one and press it in its best to take it to a machine shop do not try pressing it in yourself

Mar 09, 2010 | 2001 Volvo S40

3 Answers

Audi a4 1.9tdi quattro front wheel bearing noisy


it would be best if you let a shop fix there are some special tools needed that the shops should have.

Sep 12, 2009 | 1998 Audi A4

1 Answer

I would like to know how to change a front wheel bearing on a 03 Audi A4 1.8t quatrro


Remove the wheel, remove the dust cover from center of hub, bend and remove cotter pin...using the proper socket, break loose the hub nut (this will be on tight and may require using a properly placed prybar to keep the rotor from spinning). There are 4 or 5 bolts on the backside of the spindle, remove them, the brake caliper, rotor and the speed sensor. The hub should come out with a little force. Generally a rubber mallet used at an angle driving the hub towards you works well.

Aug 07, 2009 | 2003 Audi A4 Cabriolet

Not finding what you are looking for?
2004 Audi A4 Logo

Related Topics:

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14228 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...