Question about 1999 Ford Explorer

1 Answer

Transmission replacement: new transmission not

Transmission replacement: new transmission not fitting to bell housing,advice to pull the components closer to connect.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Master
  • 975 Answers

Make SURE the converter is seated into the trans all the way,and that the alignment dowels are not doubled up.(that is ,if one stayed in the block from the old tranny and there is also one in the new tranny in the same spot)

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm pulling a transmission out of a 95 f150 4x4.I have the transmission cooler lines disconnected, drive shaft, tranfercase,dipstick, linkage, 6 bellhouse bolts and it like something else stopping it


have you removed the bolts holding the torque converter to the flex plate as the torque converter should be pulled with the transmission and not separately
make sure that there is not a bell housing bolt from the front going back into the bell housing

Jun 16, 2016 | Cars & Trucks

2 Answers

How to replace the bell housing of a 1989 jeep wrangler 4-cyl 4x4?


why are you replacing the bellhousing?,it means you are going to have to pull out the motor or the gearbox/transfer case,whichever is easieast

Jul 04, 2014 | 1989 Jeep Wrangler

1 Answer

Cracked flywheel cover leaking oil


Do you mean the bell housing which is part of the transmission housing. if so it may pay to fit junk a yard replacement . be sure to fit a new rear crank seal, and check the clutch plate is not covered in oil.

Mar 13, 2014 | Ford Escape Cars & Trucks

1 Answer

61 apache truck 6 cylinder with 4 speed, what would all need done to fit a 350 in? I mean would tranni bolt up? I know fuel and ignition would need alittle changing and maybe the motor mounts but I...


you can get a new bell housing to fit the tranny to bolt to the new engine. you should be able to order one on-line. you will just have to make sure the tranny will handle the new engine. you will have to drop the tranny to put the new bell housing to the transmission. its not a very hard job, maybe a couple of hours

Jan 03, 2011 | 1983 Chevrolet Blazer

1 Answer

I have a rebuilt 1992 Mercedes 190e transmission, but now the transmission feels like it's slipping when I hit the accelerator. Do I need to change the transmission fluid? How long does transmission last?...


Maybe not necessarily change the fluid, but check to see if the fluid level is up to spec on the stick. Many times it will just be the fluid level that makes the transmission slip. After checking the fluid level, check under the car to see if you have a leak somewhere because you just may be able to tighten the transmission housing yourself. Generally what happens is that when a major component of the drive train is rebuilt, the gaskets and sealers need to be seated, and after a couple of heat cycles, the gaskets expand and contract, leaving a slight leak in the housing. So maybe try to tighten the bell housing on your transmission. Good luck!!

Nov 17, 2010 | 1999 Mercedes-Benz E-Class

2 Answers

Transmission fluid leaking from bell housing when in gear.


If you have never done this before,it may be best to take the truck to a shop or have some one with experience help you. You will need the truck up far enough to take out the transmission. The linkage and drive shaft has to be removed,then unbolt the transmission from the bell housing.Special tools may be needed to pull and replace the seal.
Transmission fluid needs to be changed since it is a brownish color.

Feb 16, 2010 | 1992 Ford Ranger

1 Answer

Would a 1995 toyota 4runner transmission fit in a 1994 toyota 4runner?


as long as it is the sae style of the one you pulled out. it should by all means. just make sure all the bell housing bolt holes line up with the engine and the driveline fits as well.

Nov 22, 2009 | 1994 Toyota 4Runner

1 Answer

How do i fit new slave cylinder on clutch fiesta 1997


If the slave is in the transmission trans would have to be removed in orther to replace.

Nov 16, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Loud noise coming from the transmission bell housing


If a manual transmission, look for a bad throw-out bearing, a disintegrated clutch component, or a loose flywheel--in any case, pull the transmission. If automatic transmission, the torus assembly or the flex plate may be loose or damaged. Again, pull the transmission.

Oct 11, 2009 | 1998 Jeep Grand Cherokee

2 Answers

How do I change my clutch on an 1986 suzuki samurai


I have found it easier to remove the engine to replace the clutch on my 1986 Samurai it you have the proper tools to pull the engine it took less time than pulling the transmission in my experence.

Nov 29, 2008 | 1986 Suzuki Samurai

Not finding what you are looking for?
1999 Ford Explorer Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...