Question about 2004 Toyota Corolla

Open Question

P0808 clutch postion sensor high - 2004 Toyota Corolla

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to relearn throttle body on a Lexus is250

Pedal Relearn Procedure
Accerlerator Pedal Released Postion Learning is and operation to learnicon1.png the full released postions of the accerlerator pedal by monitoring the accelerator pedal sensor output signal. It must be performed each time harness connector of accelearator pedal postion sensor or ECM is disconnected.

1. Make Sure the acceleartor Pedal is fully released
2. Turn Ignition switchON and wait at least 2 Seconds.
3. Turn ignition switchOFF and wait at least 10 Seconds
4. Turn Ignition switchON and wait at least 2 seconds.
5. Turn Ignition switchoff and wait at least 10 seconds

Throttle Valve Relearn
Throttle ValveClosed Postion Learningicon1.png is to learn the fully closed postion of the throttle valveby monitoring the throttle position sensor output signal. It must be performed each time harness of
electric throttle control actuator or ECM is disconnect.

1.Make sure accelerator pedal is fully released.
2. Turn ignition ON
3. Turn igntion switch OFF and wait at least 10 seconds. Make sure that the throttle valvemoves during the 10 seconds by confrming the operating sound.
(You can hear the TB sound when you have key on and shifter in first gear and step on the gas. So you know what you listening for.)

Idle Air Volume Relearn Procedure
The Following Condtions Must be met in order for procedure to Work.

Battery Voltage :More than 12.9 volts at idle
Engine Coolant Temp 158-203 degrees Farenhiet
Electric Load Switch OFF i.e Air Condition, headlamps , rear defogger
Steering Wheel: Neutral Postion (Straight Ahead)
PNP Switch: OFF (Park Neutral Switch i.e. Clutch Switch...pretty sure)

3. Start engine and warm it up to operation temperature
4. Turn igniton switch OFF and wait at least 10 seconds
5. Confirm Gas Pedalif fully realeased, then turn igniton switch ON and wait 3 seconds
6. Fully step on and release gas pedal5 time within 5 seconds
8. Wait 7 seconds and fully step on gas and stay on until MIL stops blinking and is steady.
9. Fully release the Gas pedalwithin 3 seconds after the MIL has turned ON steady.
10. Start engine imediatly and let idle. Wait 20 seconds.

Sep 22, 2014 | Lexus IS 250 Cars & Trucks

1 Answer

Engine idles to high

easy ..........throttle postioning sensor ,or your throttle is sticking meaning your throttle cable isnt moving in an out properly

Feb 07, 2013 | Cars & Trucks

1 Answer

Car idles

If it revs up and down you need retrain the car to idle. I know it sounds crazy but you need to ask dealer or local shop the steps to do it.

Dec 31, 2009 | 2002 Dodge Neon

1 Answer

Bank 2 is that the sensor on the right side on the pipe

Bank 2 is passenger side. And if you are talking about o2 sensors then postion 1 is closer to the eninge, and postion 2 is further away. SO... Bank 2 postions 2 would be the passenger side rear o2 sensor (that was just an exsample of what a code could be)
Good luck.

Nov 09, 2009 | 2000 Chevrolet Silverado

1 Answer

I have 97grandam it surges when you let off the gas it idels high around 1500 i was told map sensor don't know where it,located it'2.4

a high idle is caused by only a couple of things, one is a Throttle postion sensor, another is a defective Idle speed control valve and th last is a intake manifold vacuum leak.

Jun 12, 2009 | 1996 Pontiac Grand Am

1 Answer

Blwr. mtr. fuse blows when a/c is turned on

May check your A/C Diode for failure.Hope this helps

May 16, 2009 | 1995 Ford Contour

Not finding what you are looking for?
2004 Toyota Corolla Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides