Question about 2001 Mazda 626

1 Answer

How to remove and change crank shaft pulley on 2001 mazda 626

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Mazda Master
  • 1,453 Answers

You have to partially unscrew the bolt in the center, that's holding the pulley to the crankshaft. Then, you have to use a puller to safely pull, without damaging, the pulley off the crankshaft. When it gets pulled away, off the crankshaft, remove the puller, unbolt the center bolt all the way and take the pulley out.

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is timing belt installation sequence on a 1999 Mazda 626 6 cylinder?


set mark on crankshaft to TDC mark on timing cover. set mark on cam pulley to align with mark on head .if more than one mark on pulley rotate by hand till exhaust and inlet just rocking then align closest marks .

May 11, 2014 | Cars & Trucks

1 Answer

How 1996 mazda 626 front axle shield broken


The drive shaft has to be removed to replace the rubber boot .you will have to dismantle the CV joint , clean and repack the joint with special grease and fit a new boot.

May 10, 2014 | 2001 Mazda 626

1 Answer

Looking for the location of crank shaft on 2000 mazda 626


i assume you mean crank shaft sensor ,if its not on the front puilley then look around the bell housing in the most extreme awkard in accessable position possible because you can bet that is where it is

Jun 14, 2010 | 2000 Mazda 626

2 Answers

Where is the crank sensor located on a chevy malibu 2001


It should be down near the crankshaft pulley. Remove the the right front wheel and the splash shield, it should be there next to the pulley.

Dec 20, 2009 | 2001 Chevrolet Malibu

1 Answer

Where is the timing mark on the cam-shaft pulley for mazda 626/1991


12 o clock straight up, should be a mark, the dowel pin on the cam should be straight up also

Sep 01, 2009 | 1992 Mazda 626

2 Answers

Mazda stalls


I have a 1997 626 2.0L 5speed when im driven it like rev limits cuts out around 3500-4000rpm, and when i rev it up and past 4000rpm it stalls, anyone have a idea whats wrong??? thanks i just replaced the crank sensor and egr and still. good power put cuts out

Jul 03, 2009 | 1997 Mazda 626

1 Answer

Coolant leak at crank pulley


it is not the crank pulley it is the water pump above the crank pulley, the coolant runs down and looks like it is from the pulley area.

Jun 20, 2009 | 1994 Mazda 626

1 Answer

Mazda 626 with no spark


be for you dig to deep into something like that take off the distributor cap and then pull off the rotter and check your connection at that point. that part might have to be changed

Mar 23, 2009 | 1994 Mazda 626

1 Answer

Reduced arc, wipers. Park in center of glass.


he bracket and the crank usually go inline, in experience usualy the crank folds around and the bolt is underneath the arm, though try both ways if first fails. good luck.Davelee

Jan 29, 2009 | 1995 Mazda 626

1 Answer

Mazda 626 1992 2litre dohc timing case oilseal


there ar two oil seals on your vehicle one is located behind crankshaft pulley and the other is located at rear input shaft to transmission you will need to remove your crankshaft pulleys including pulley boss or transmission and flywheel and torque converter if automatic to change seals are fairly cheap and easy to remove just follow steps in repair manual from local parts store. Or take it to a shop lol.

Oct 19, 2008 | 1992 Mazda 626

Not finding what you are looking for?
2001 Mazda 626 Logo

469 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...