Question about 1991 Chevrolet Cavalier

1 Answer

How do you remove and reinstall a oil pan on a chevy cavalier z24 3.1 v6 automatic

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt and the tensioner.
  3. Support the engine with tool J-28467 or equivalent.
  4. Raise and safely support the vehicle. Drain the engine oil.
  5. Remove the starter shield and the flywheel cover. Remove the starter.
  6. Remove the engine to frame mount retaining nuts.
  7. Lower the vehicle.
  8. Support the engine using tool J-28467-A or equivalent, then raise and support the vehicle safely.
  9. Remove the right tire and wheel assembly. Remove the right inner fender splash shield.
  10. Unfasten the oil pan retaining bolts and nuts and remove the oil pan.
how do you remove and reinstall a oil pan on a - 6572b9f.jpg

To install:
  1. Clean the gasket mating surfaces.
  2. Install a new gasket on the oil pan. Apply silicon sealer to the portion of the pan that contacts the rear of the block.
  3. Install the oil pan retaining nuts. Tighten the nuts to 71-89 inch lbs. (8-10 Nm).
  4. Install the oil pan retaining bolts. Tighten the rear bolts to 18 ft. lbs. (25 Nm) and the remaining bolts to 71-89 inch lbs. (8-10 Nm).
  5. Install the right inner fender splash shield.
  6. Lower the vehicle and remove the engine support tool.
  7. Raise and support the vehicle safely.
  8. Install the engine to frame mounting nuts.
  9. Install the starter and splash shield. Install the flywheel shield.
  10. Lower the vehicle and fill the crankcase with oil, install the belt tensioner and belt and connect the negative battery cable. Run the engine to normal operating temperature and check for leaks.
Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change a gasket on the oil pan I have a 99 Chevy Cavalier


Drain the oil and remove the screws/bolts that hold the pan into place.

Then use a flat-blade screwdriver to gently prise the pan free.

Clean both mating surfaces of pan and block - remove all traces of the old gasket.

Smear some sealant compound on the oil pan - this will hold the new gasket in place. Put the new gasket onto the oil pan and align the bolt holes. Lift the pan into place and tighten the bolts.

The photo below is a generic image of oil pan with gasket.




26061843-wygqn0rnpnipldbddgjc2eqg-5-0.jpeg


26061843-wygqn0rnpnipldbddgjc2eqg-5-1.jpg

Jan 20, 2016 | Cars & Trucks

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

Change oil pan


drain oil by removing the drain bolt from the oil pan. then remove oil pan bolts around edges of pan located under car at bottom of motor. my hav to remove a brace or two if the pan will not come out freely. clean all surfaces no oil or gasket material, add rtv silicone sealant and reinstall pan

Oct 20, 2012 | 2002 Chevrolet Cavalier Coupe

1 Answer

Wher is the oil pump mounted on a 1989 Chevy Cavalier Z24 2.8 Liter motor


OIL PUMP IN THE OIL PAN.YOU HAVE TO REMOVE OIL PAN TO GET TO OIL PUMP.

Nov 18, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

How do you change the transmisson filter on a 1996 chevy cavalier


look underneath the car. you will see the oil pan and another pan on the drivers side. take all the bolts out of that pan. NOT THE OIL PAN. and drain the fluid. remove all the old gasket material. change the filter. it will be obvious. and reinstall. be careful not to over tighten the bolts on the pan you will split the gasket and it will leak like a siv.

May 12, 2010 | 1996 Chevrolet Cavalier

1 Answer

Fluid capacity of a 4 speed auto in 1998 cavalier?


9.5 quarts
The check hole is located near the oil drain plug.

Jan 25, 2010 | 1998 Chevrolet Cavalier

1 Answer

2005 Chevy Cavalier, oil pan has hole from rock. Removed all bolts but still cant get pan off. Does engine need to be supported by something during process and what can the pan be caught on


most of front end and engine cross over support--if hole is small enough clean and make a plug with pop rivet and cold weld epoxy(oil & gas proof) or if bigger use rubber oil plug replacement a plug about 1/2 inch wide used as replacement when oil drain plug damaged or cross threaded most auto stores sell them

Oct 25, 2009 | 2005 Chevrolet Cavalier

1 Answer

2000 chevy cavalier oil pan....2.2 lit....auto


put car on stands

remove right side engine splash shield

remove exhaust shield

remove AC brace at starter/ compressor bracket

remove flywheel inspection plate

remove engine mount strut, remove bolts from bracket. Lower the bracket slightly to gain clearance to remove pan.

remove oil filter extension (auto trans. only)

remove all pan bolts

tap pan with rubber hammer to break old gasket loose from block.

clean all used gasket off and install is reverse

Mar 13, 2009 | 2000 Chevrolet Cavalier

Not finding what you are looking for?
1991 Chevrolet Cavalier Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...