Question about 1998 Ford Explorer

1 Answer

Transmission code obdcode p1762 keeps coming up and won,t pass n,y, state inspection what is problem

Posted by on

  • Danny Kaye Oct 10, 2008

    I need to buy or download a Ford Ka 2005 Workshop Manual with OHC Timing Chain 'metal' not tooted belt 1.3 liter Engine. Regards.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 114 Answers

Here is the TSB from Ford:


Here it is... TSB 03-22-10...

FORD: 1995-2001 EXPLORER
1995-2002 RANGER
1996-1997 AEROSTAR
2000-2002 EXPLORER SPORT
2001-2002 EXPLORER SPORT TRAC
MERCURY: 1997-2001 MOUNTAINEER


This article supersedes TSB's 03-11-9, 02-13-8 and 02-08-2 to update the model coverage.

ISSUE:
Some vehicles built prior to 12/1/2001 may exhibit the following shift and engagement conditions:

No 2nd Gear
No 3rd Gear
No Engine Braking In Manual 1st.
Out of specification pressures controlled by the transmission main control valve body separator plate may be the cause.

ACTION:
Verify the condition, the main control valve body separator plate may need to be updated to the latest level. Refer to the following Service Procedure for details.

SERVICE PROCEDURE

CAUTION: A NEW SEPARATOR 7Z490 MUST BE USED WHEN INSTALLING THE SPECIAL SERVICE KIT 7M203 OR ADDITIONAL TRANSMISSION DAMAGE MAY OCCUR. REFER TO THE PARTS APPLICATION CHART IN THIS ARTICLE FOR CORRECT SEPARATOR PLATE PART LISTING.



NOTE: THIS ARTICLE DOES NOT APPLY TO ANY OTHER CONDITIONS OR COMPONENTS THAT MAY CAUSE SIMILAR SYMPTOMS AND IS ONLY WRITTEN TO COVER THESE SPECIFIC CONDITIONS.



NOTE: AN IN-LINE SERVICE FILTER IS NOT REQUIRED TO BE ADDED OR REPLACED FOR THIS TSB.



Verify that one or more of the following conditions exist.
Low Line Pressure While In Drive At WOT
No 2nd And/Or No 3rd Gear
No Engine Braking In Manual 1st
DTC P0732, P0733 Or P1762
Install Kit (3L5Z-7M203-JA) to update the main control valve body assembly, refer to the installation procedures found in the kit.
Reinstall the main control by continuing to follow the installation steps listed in the Workshop Manual, in-vehicle service, main control valve body.
After completing the procedure, verify the condition has been corrected.
Clear all DTCs.

Part Application Chart
Vehicle Application Engineering Description Qty. New Service Part Use on Transmission Application 7000 -Reference Only-
95/96 Models ONLY
95/97 Models Separator Plate to Case Gasket 1 2L5Z-7C155-AA ALL
95/97 Models Separator Plate to Main Control Gasket 1 2L5Z-7D100-BA ALL
95/96 Models - ALL Plate - Valve Body Separator 1 F5TZ-7A008-CA 95GT-AA/BA/CA/DA/EA/FA/ GA;96GT-BA/CADB/EB/FA/ GA/HA/KA/MA/NA
97 Models ONLY
97 2.3L Ranger Plate - Valve Body Separator 1 F77Z-7A008-AB 97GT-GC
97 3.0L OHV Ranger/Aerostar Plate - Valve Body Separator 1 F77Z-7A008-AB 97GT-EC/FC/MC/NC/RE/SE
97 4.0L OHV Ranger/Aerostar Plate - Valve Body Separator 1 F77Z-7A008-CB 97GT-KE/LE
97 4.0L OHV Explorer/Mountaineer Plate - Valve Body Separator 1 F77Z-7A008-DB 97GT-KF/LF
97 4.0L SOHC Explorer/Mountaineer Plate - Valve Body Separator 1 F77Z-7A008-EB 97GT-AE/BE
1998-2001 Models ONLY
98/01 2.5L Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-DA 98GT-GA; XL5P-CA
98/00 3.0L Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-EA 98GT-EB/FB; XL5P-AA/BA
98/00 4.0L - EI Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-FA 98GT-KB/LB; XL5P-DA/EA/FA
98/00 4.0L - EI Explorer Plate - Valve Body Separator 1 1L5Z-7Z490-GA 98GT-CB/DB; XL2P- EA/FA
98/00 4.0L - SOHC Plate - Valve Body Separator 1 1L5Z-7Z490-HA 98GT-AA/BA; XL2P- CA/DA
2001-2002 Models ONLY
2001/2002 2.3L Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-AA 1L5P-CA
2001/2002 3.0L Ranger Plate - Valve Body Separator 1 1L5Z-7Z490-BA 1L5P-AA/BA
2001/2002 4.0L-SOHC - ALL Plate - Valve Body Separator 1 1L5Z-7Z490-CA 1L5P-DA/EA
ALL MODELS
1995-2002 ALL as Listed Above Valve Body Service Kit 1 3L5Z-7M203-JA ALL

Posted on Jun 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Jeep shows p1762 code only after wet weather limps, after dried and code cleared jeep drives great until it rains...


You have worn wire/s. They are inaccessible unless you remove the cross member and drop the transmission as far as it will go down. Then it is still difficult to repair the wire/s. You need a pinout of the plugs and just run a new wire. I don't have a 97. if I did, I would surely pass it on to you.

Aug 12, 2015 | 1997 Jeep Grand Cherokee

1 Answer

Trouble code p1762


Code p1762 is the governor pressure offset volts too high or too low. This is a transmission solenoid that probably needs replaced. I believe that you have to take the pan off to get at it.

Apr 13, 2014 | 2001 Dodge Dakota

1 Answer

I have a code p1762 for my 97 jeep grand cherokee


Trouble code P1762 means: Governor pressure sensor offset improper voltage. Gov. Pressure Sensor.It is located in the valve body of the transmission and requires dropping the transmission pan to replace. Sounds much more difficult than it is. Since you have to change your fluid it's a good idea to change the trans. filter .

Feb 01, 2011 | 1997 Jeep Grand Cherokee

1 Answer

I need to know what diagnostic code p1762 means


Dodge: Governor pressure sensor offset improper voltage Dodge: Governor pressure sensor offset improper voltageFault Code P1762: Automatic transmission Governor pressure sensor offset improper voltage

Sep 30, 2010 | Dodge Pickup Cars & Trucks

1 Answer

What do these codes mean? P1763 and P1762


Those codes indicate an issue with the Governor pressure sensor and the transducer which you'll have to replace. To replace them you'll have to drop the transmission pan to see them. Remove the bolts and disconnect the wiring clips to remove them.

Nov 19, 2009 | 1999 Dodge Durango

1 Answer

I have a ODB II code reader giving p1763, p1762, p0303


Your right about the two codes. It's really a transmission part.
As soon as you open up the transmission pan, it right there.
f0d99d5.jpg But, I would leave this up to a transmission place. It may need a special type of calibration tool for the new sensor.

As for PO303, that is a missfire in cylinder #3

I hope I answered your question.

Mar 27, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Transmission code


p1762 is a specific fault of overdrive band off

Aug 24, 2008 | 1997 Ford Explorer AWD

Not finding what you are looking for?
1998 Ford Explorer Logo

1,830 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...