Question about 2006 Jaguar XJ8

1 Answer

How to change front brake pads - 2006 Jaguar XJ8

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Jaguar Expert
  • 196 Answers

The front brakes are straight forward, open the brake fluid reservior,remove tires,then the caliber,then remove pads and use a c-clamp to compress the calibers,,install new pads,,the reinstall the cap on the fluid reservoir,when you crank the car,pump the brakes three times and on the last pump hold the paddle to floor then pull the electronic park brake. you will hear the module reset....

Posted on Nov 21, 2012

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22219 Answers

SOURCE: how do I change the brake pads

piece of cake ,the pistons just push in front and rear ,the handbrake is inside the rear brake disk so dont forget to strip and lubrcate the operating mechanisms for the handbrake with some nice copperslip in the adjuster .Also most important is to polish it every week and clean seats with leather restorer every month after all it is a real car as its a JAGUAR

Posted on Jul 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What tools do i need to change brake pads on 2005 yukon xl


Jack, wheel wrench, socket set, large screw driver, pair of pliers or grips. Lithium grease for the pins. Watch all of these videos. .spell{font-size:18px}.spell_orig{font-size:15px}#mss p{margin:0;padding-top:5px}




g-img{display:block}._WCg{display:block;border:0;position:relative} Search Results

    How To Install Replace Front Brake Pads 2000-06 Chevy ...

    9k=? 4:46 https://www.youtube.com/watch?v=nPohZtD8zlA May 27, 2014 - Uploaded by 1A Auto Parts http://www.1aauto.com/brake-pads/i/1abps00080 1A Auto shows you how to ... Front Brake Pads 2000-06 ...

    HOW TO INSTALL REPLACE GMC YUKON DENALI ...

    z? 14:10 https://www.youtube.com/watch?v=um7dt_yvZ1s Sep 20, 2012 - Uploaded by TheRykerDane Video on how to change the brake pads and rotors on a 2004 GMC Yukon Denali. Changing these parts ...

    How to REPLACE INSTALL BRAKES and ROTORS GMC ...

    2q==? 11:32 https://www.youtube.com/watch?v=UWqows3P4DE Feb 11, 2012 - Uploaded by TheRykerDane Video on how to change the brake pads and rotors on a 2004 GMC Yukon. Changing these parts ... Would ...

    GMC Denali Brake Pads Removal and Installation - YouTube

    z? 3:45 https://www.youtube.com/watch?v=uEKs8nphVxU Oct 24, 2012 - Uploaded by AnotherLookFilms Remove and Install rear brake pads on your 2006 GMC Denali XL. ... 9-21-13 2007 GMC Yukon rear brakes ...

    GMC Yukon Denali Front Disc Brake Pad Replacement ...

    2q==? 8:21 https://www.youtube.com/watch?v=w_gn_l5lYkw Jun 20, 2013 - Uploaded by AMS Automotive Watch the proper procedure for replacing front disc brake pads. Featured vehicle: 2007 GMC Yukon Denali ...





Jan 22, 2016 | Cars & Trucks

1 Answer

Change brake pads


For starters the front and rear us disk pads and it is not hard to do. On the front jack up the front and us jack stand for safety. After you take of the wheel remove the two bolts at the back of the brake caliper remove the caliper and then the old pads us a C- clamp with one of the old pads installed in the caliper then just us the c-clamp to push the cylinder all the way in until it will go no further install new pads put back on. But before you do the next side hit the brake to push the cylinder back out. Go to other side do the same thing. On a side not you only need to replace the rear brakes every other time you do the front. The front wear twice as fast as they do most of the stopping.

May 19, 2013 | 2004 Buick Century

1 Answer

I have a F150 p/u 2000 for 10yrs. Each year I change the brake pads. But the rear pads still looks like new. The front pads are worn down. What can be causing the problem?


normally, you replace the rear brake pads every other change in the front brake pads. for your case, it seems that the front brakes are the only ones working.

bleed your brakes to check if rear brakes are still working. after bleeding, check your brake master if it puts pressure equally to the 4 brakes.

Aug 05, 2011 | Ford F-150 Cars & Trucks

1 Answer

I want to change my front brake pads How do I remove the old ones


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Apr 12, 2011 | Volkswagen Polo Cars & Trucks

2 Answers

Change brake pads


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Sep 30, 2010 | Audi A6 Cars & Trucks

1 Answer

Anything special about changing front pads on audi a3? I've done honda, acura and toyota's.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Aug 25, 2010 | 2007 Audi A3

1 Answer

Changing rear brake pads


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Please rate my response. Thanks!

Apr 09, 2010 | 1999 Volkswagen Passat

1 Answer

Squealing sound - front driver's side brakes


This sounds like a wear indicator( a metal tab on the brake pad) is doing its job, warning you that the brake pads need replacement soon. you can bend the wear indicators away from the rotor so they won't make contact. This will stop the annoying noise. Replace the pads and check the brakes soon. Brake pads should always be changed on both wheels at thge same time, so change the other front pads also.

Nov 27, 2009 | 2002 Kia Sportage

2 Answers

Change hyundai accent 2001 front brake pads


may have siezed caliper slide pins suggest buy reman loaded caliper assembly

Oct 05, 2009 | 2001 Hyundai Accent

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

Not finding what you are looking for?
2006 Jaguar XJ8 Logo

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...