Question about 1993 Buick LeSabre

1 Answer

Water leaks from the throttle body. Have replaced gaskets and tightened system twice - What should I do?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Cleane old gasket and replase throtttle or bypass it whis rubber hose

Posted on Oct 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Throttle body sensor location 2005 uplander


the sensor is part of the throttle body and not replaceable here is the throttle body replacement instructions as you will have to replace the entire throttle body it is a very common issue with these
THROTTLE BODY ASSEMBLY REPLACEMENT

REMOVAL PROCEDURE
  1. Remove the air cleaner intake duct.
120434113
  1. Disconnect the electronic throttle control (ETC) electrical connector (1) from the throttle body (2).
113356645
  1. Remove the heater pipe nut at the throttle body.
  2. Remove only the heater inlet pipe.
113356646
  1. Remove the nuts and the bolts from the throttle body.
  2. Remove the throttle body assembly.
  3. Remove the throttle body gasket.
  4. Clean and inspect the throttle body gasket mating surfaces.
NOTE: Do not use solvent of any type when cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as damage to the gasket surfaces and throttle body assembly may result.

Use care in cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as sharp tools may damage the gasket surfaces.

INSTALLATION PROCEDURE
113356646
  1. Install a new gasket, if necessary.
  2. Install the throttle body assembly.
  3. Install the throttle body nuts and the bolts.
NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the nuts and the bolts to 10 N.m (89 lb in) .
113356645
  1. Install the heater inlet pipe.
  2. Install the heater pipe nut to the throttle body.
Tighten the nut to 25 N.m (18 lb ft) .
120434113
  1. Connect the ETC electrical connector (1) to the throttle body (2).
  2. Install the air cleaner intake duct.

Feb 03, 2014 | 2005 Chevrolet Uplander

1 Answer

How do you install a thermostat on a 2001 suburban?


  1. Standing in front of the vehicle it's on the left front side of engine kind of low.
  2. Be sure to get a gasket as well.
  3. Drain the cooling system.
  4. Loosen the air cleaner outlet duct clamps at the following locations:
    • Throttle body
    • Mass airflow/intake air temperature (MAF/IAT) sensor
  5. Remove the radiator inlet hose clip from the outlet duct.
  6. Remove the air cleaner outlet duct.
  7. Reposition the outlet hose clamp at the water pump.
  8. Remove the outlet hose from the water pump.
  9. Remove the water pump inlet bolts.
  10. Remove the water pump inlet and thermostat from the water pump. Water pump inlet/thermostat assembly location
To install:

  1. Install the thermostat and water pump inlet to the water pump.
  2. Install the water pump inlet bolts.
  3. Tighten the water pump inlet bolts to 11 ft. lbs. (15 Nm).
  4. Install the outlet hose to the water pump.
  5. Position the outlet hose clamp at the water pump. NOTE
    Important: Align the arrow at the throttle body end of the duct with the throttle body attaching stud.
  6. Install the air cleaner outlet duct.
  7. Install the radiator inlet hose clip to the outlet duct.
  8. Tighten the air cleaner outlet duct clamps at the following locations:
    • Throttle body
    • Mass airflow/intake air temperature (MAF/IAT) sensor
  9. Tighten the air cleaner outlet duct clamp screws to 62 inch lbs. (7 Nm).
  10. Fill the cooling system and check for leaks.

Read more: http://wiki.answers.com/Q/Where_is_the_thermostat_located_on_a_2001_chevy_suburban#ixzz1TvIO3kpD

Aug 03, 2011 | 2001 Chevrolet Suburban

1 Answer

I have a 2005 f150 with a 5.4 and am getting a code po506 what is this!


PO506 --- Idle Air Control System RPM lower then expected

Clean Throttle Plate
Check for any air/vacuum leaks --

Ducting from air filter to throttle,loose or a vacuum leak
Throttle Body Leaking
MAF Sensor
IAC Valve gasket
Egr Gasket
PCV Seal

Hopefully you have installed new spark plugs since 2005
Also replaced the front (2) O2 Sensors at 100,000 miles
Cleaned MAF Sensor once or twice a year

Jul 12, 2011 | Ford F-150 Cars & Trucks

2 Answers

2001 daewoo leganza water is entering to the oil could the throttle body gasket need replaced?


No has no way to internally get water into engine. Most likely head gasket, in some cars the intake gasket could leak coolant into the crankcase.

Jan 29, 2011 | Daewoo Leganza Cars & Trucks

3 Answers

How do I remove the head? (Blown Head gasket)


prev.gif next.gif Cylinder Head REMOVAL & INSTALLATION 2.3L Engine
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable, then drain cooling system into a suitable container.
  3. Detach the heater inlet and throttle body heater hoses from water outlet. If accessible at this time, disconnect the upper radiator hose from the water outlet.
  4. Remove the exhaust manifold. For details, please refer to the procedure located in this section.
  5. Remove the intake (camshaft housing for SOHC) and exhaust (DOHC only) camshaft housings.
  6. Unfasten the oil fill tube bolt/screw then remove the oil fill cap and level indicator assembly. Pull the oil fill tube upward to unseat from block.
  7. Label and disengage the injector harness electrical connector.
  8. Detach the throttle body-to-air intake duct.
  9. Tag and disconnect the power brake vacuum hose from the throttle body.
  10. Remove the throttle cable bracket.
  11. Remove the throttle body from the intake manifold with the electrical harness and throttle cable attached and position the assembly aside.
  12. Tag and disconnect the MAP sensor vacuum hose from the intake manifold, then remove the intake manifold brace.
  13. Detach the electrical connectors from the MAP sensor, IAT sensor and the EVAP canister purge solenoid.
  14. If not already done, detach the upper (inlet) radiator hose from the water outlet.
  15. Disengage the coolant temperature sensor connector(s).
  16. Unfasten the cylinder head bolts in reverse order of the installation sequence shown in the accompanying figures.
  17. Lift the cylinder head from the engine block. Remove and discard the gasket. Inspect the oil flow check valve for freedom of movement.
  18. Using a suitable solvent, thoroughly clean and dry all bolts, bolt holes and mating surfaces. Inspect the head bolts for any damage and replace, if necessary. If using a scraper to clean the old gasket material from the mating surfaces, use only a plastic or wood one, NOT a metal scraper. Do NOT allow any debris to fall into the engine! To install:
  19. Place a new cylinder head gasket on the cylinder block, then carefully position the cylinder head in place.
  20. Sparingly coat the head bolt threads with clean engine oil, then allow the oil to drain off before installing.
  21. On 1988-89 engines, install and tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten all head bolts in sequence to 26 ft. lbs. (35 Nm)
    • Step 2 - Using a torque angle meter, tighten the short bolts an additional 80°and the long bolts an additional 90°in sequence Fig. 5: Cylinder head bolt tightening sequence - 1988-89 2.3L engine 86883121.gif
  22. On 1990-91 engines, tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten all head bolts in sequence to 26 ft. lbs. (35 Nm)
    • Step 2 - Using a torque angle meter, tighten the short bolts an additional 100°and the long bolts an additional 110°in sequence Fig. 6: Cylinder head bolt tightening sequence - 1990-91 2.3L engine 86883122.gif
  23. On 1992 engines, tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten, in sequence, head bolts 1-6 to 26 ft. lbs. (35 Nm), 7-8 to 15 ft. lbs. (20 Nm) and 9-10 to 22 ft. lbs. (30 Nm).
    • Step 2 - Tighten all head bolts, in sequence, an additional 90°using J 36660 or equivalent
    • Step 3 - In sequence, loosen each bolt one turn, then immediately re-tighten to the specified torque
    • Step 4 - After completing step 3 on all 10 bolts, tighten each bolt, in sequence, an additional 90° Fig. 7: Cylinder head bolt tightening sequence - 1992 2.3L engine 86883123.gif
  24. On 1993-95 vehicles, tighten the cylinder head bolts to the specifications shown in the accompanying figures. Fig. 8: Cylinder head bolt tightening sequence and specifications - 1993 2.3L engine 86883124.gif
    Fig. 9: Cylinder head bolt tightening sequence and specifications - 1994-95 2.3L engine 86883125.gif
  25. Engage the coolant temperature sensor electrical connector(s).
  26. Connect the upper radiator hose to the water outlet.
  27. Install the intake manifold bracket.
  28. Attach the following electrical connections: MAP sensor, IAT sensor, and the purge solenoid.
  29. Using a new gasket, install the throttle body to the intake manifold.
  30. Install the accelerator control cable bracket.
  31. Connect the throttle body-to-air intake duct.
  32. Install the oil fill tube and level indicator.
  33. Install the camshaft housing(s).
  34. Install the exhaust manifold. For details, please refer to the procedure located in this section.
  35. Connect the heater inlet and throttle body heater hoses to the water outlet.
  36. Fill all fluids to their proper levels.
  37. Connect the battery cable, start the engine and check for leaks.

Sep 24, 2010 | 1992 Oldsmobile Achieva

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

1 Answer

I own a impala 2003 and i would like to know how to change the thermostat on it.The motor is a 3.4 liters


Drain radiator. Remove upper rad hose from thermostat housing. Disconnect air intake hose from throttle body. Remove throttle body from upper intake manifold, disconnecting the 2 rubber hoses to the heater line. You may also need to disconnect the fuel line. Remove the exhaust crossover heat shield and loosen the crossover pipe from both exhaust manifolds but don't remove crossover completely. You should have access to the 2 thermostat housing bolts, remove upper bolt but just loosen the lower one about a half inch. Pull the housing out and up from the intake manifold to access the thermostat. Clean the mating surfaces with a gasket remover. replace thermostat, apply a light coating of rtv sealant to both sides of the new gasket. Replace thermostat housing with the gasket to the intake manifold. Apply some rtv to the bolt threads before reattaching housing. Tighten bolts snugly but do not over tighten. Tighten exhaust crossover and reattach the heat shield. Install throttle body attaching the 2 little hoses at the bottom, its a good time to replace these hoses and clamps. Depending on the condition of the throttle body gasket you may need to replace it also. Reconnect the fuel line (if disconnected) Reconnect air intake hose to throttle body. Reattach the upper rad hose to housing. Fill rad with coolant 50/50 mix with water (make sure to use the same type antifreeze that is in the system, they say you can mix green with red but I wouldn't recommend) Leave rad cap off start the car and let it warm up until you can see the coolant circulating and ad coolant as necessary until full. Now there is going to be some air in the system that you need to bleed out. There are 2 bleeders on this system, 1 is on the top of the thermostat housing, and the other is on the metal heater line on top of the water pump (the one that goes across the front of the engine and around under the throttle body that the two little hoses attach to) Bleed the one on the housing first (its the lower one) open it until fluid comes out then tighten it. Then move to the 1 on the heater line(above water pump) loosen it until fluid comes out the re-tighten. Fill recovery tank to fill line replace the rad cap and take it for a ride, watching the temp gage closely. If the temp goes higher than normal than there is probably more air in the system. you'll have to bleed it again.
This is a very labor intensive procedure and I do recommend buying or checking a service manual out from your local library. I've done these in the past and to be honest I just have the dealer do it now. A system flush and thermostat replacement was around $230 the last time I had it done, but it comes with a warranty. And you wont have to rent or buy a fuel line disconnect tool if you end up having to disconnect it. These are the hardest thermostats I've ever replaced.

Jun 09, 2010 | 2003 Chevrolet Impala

2 Answers

Leaking coolant from pipe behind throttle body..


Look for a loose water or coolant hose .
Re tighten it and you will be OK .
If the problem is that it leaks the engine gasket then you may need to reinstall new gasket but this involves a lot of work.
A good light and a good mirror is what you need to see better where the leak is coming from .

Dec 11, 2009 | 1990 Oldsmobile Silhouette

1 Answer

How to replace a water pump on a 2003 yukon


Water Pump Replacement (4.8L, 5.3L and 6.0L Engines)
Removal Procedure
1. Drain the cooling system.
2. Loosen the air cleaner outlet duct clamps at these locations:
 Throttle body
 Mass Airflow/Intake Air Temperature (MAF/IAT) sensor
3. Remove the radiator inlet hose clip from the outlet duct.
4. Remove the air cleaner outlet duct.
5. If necessary, remove the engine sight shield.
6. Remove the radiator vent inlet hose from the radiator hose clips.
7. Reposition the inlet hose clamp at the water pump.
8. Remove the inlet hose from the water pump.
9. Remove the fan blade.
11. Reposition the outlet hose clamp at the water pump.
12. Remove the outlet hose from the water pump.
13. Reposition the surge tank outlet hose clamp at the water pump.
14. Remove the surge tank outlet hose from the water pump.
15. Reposition the heater inlet hose clamp at the water pump.
16. Remove the heater inlet hose from the water pump.
17. Remove the water pump bolts.
18. Remove the water pump and gaskets.
19. Discard the water pump gaskets
Installation Procedure Important: All gaskets surfaces are to be free of oil or other foreign material
during assembly.
1. Install the water pump and NEW gaskets
2. Install the water pump bolts.
3. Install the heater inlet hose to the water pump.
Zoom Sized for Print
Notice: Refer to Fastener Notice in Service and Precautions.
2.1. Tighten the bolts a first pass to 15 Nm (11 ft. lbs.).
2.2. Tighten the bolts a final pass to 30 Nm (22 ft. lbs.).
4. Position the heater inlet hose clamp at the water pump.
5. Install the surge tank outlet hose to the water pump.
6. Position the surge tank outlet hose clamp at the water pump.
7. Install the outlet hose to the water pump.
8. Position the outlet hose clamp at the water pump.
9. Install the accessory drive belt.
10. Install the fan blade.
11. Install the inlet hose to the water pump.
12. Position the inlet hose clamp at the water pump.
13. Install the engine vent inlet hose to the radiator hose clips.
14. If necessary, install the engine sight shield.
Important: Align the arrow at the throttle body end of the duct with the throttle
body attaching stud.
15. Install the air cleaner outlet duct
16. Install the radiator inlet hose clip to the outlet duct.
17. Tighten the air cleaner outlet duct clamps at these locations:
 Throttle body
 MAF/IAT sensor Tighten the clamps to 7 Nm (62 inch lbs.).
18. Fill the cooling system.

I hope this helps. The numbering is incorrect in the sequence but the instructions are correct.

Roy

Nov 06, 2009 | 2003 GMC Yukon

2 Answers

Water is seaping out betwean the intake and head do you think it could just be an intake gasket its leaking toward the throttle body


if its leaking next to throttle body shift cable side where intake is. its the intake gasket leaking.if its leaking under the throttle body.check top radiator hose.it could be leaking also.

Jul 18, 2009 | 2000 Chevrolet Impala

Not finding what you are looking for?
1993 Buick LeSabre Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...