Question about 2005 Mitsubishi Endeavor

Open Question

How do I replace the rear knuckle bushings? - 2005 Mitsubishi Endeavor

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: How do You replace bushings in a Cadillac Rear Knuckle?

these bushings press out of the knuckle in only one direction yes they are replaceable and available for aftermarket you can call me 1-270-746-9850 and i can explain how to press them in and out had the same problem with my secretary's caddy and we replaced them and no problems since


Thanks

Posted on Dec 04, 2008

  • 9 Answers

SOURCE: Rear Suspension Knucle bushing

i found them at gmbushings.com didn't have to buy the whole knuckle

Posted on May 08, 2009

markfreedman
  • 312 Answers

SOURCE: my car sways from side to side i was told the

Hi,
Your car is swaying side-to-side because of a really serious suspension issue. It needs immediate attention. Like NOW. What can happen with no warning whatsoever is that you can instantly loose total control of the car. That translates into a potentially very serious accident. Such as going down the road at 70 miles and hour and suddenly flipping over a 6 times and then shooting across the median into a van full of children and everyone gets killed. Not the type thing you plan on.
Am I exaggerating? No!
If you are going to fix the car yourself. Using a good quality jack. First, to answer your question, jack up each rear wheel and remove the tire and examine the suspension system parts. You will find some sort of component that is very loose. Such as a bushing that has no rubber left in it, or a ball joint that is about to let go. If it is a bushing, then it is not as serious. If it is a worn ball joint, it may not be so easily detected. However a worn ball joint is deadly serious.
If you are not a skilled fix it yourself type of person, then the next trip or tow should be to a honest certified mechanic. I'm not exaggerating when I describe what can happen. A good friend of mine in a relatively new SUV flipped over the edge of a bridge with his young wife in the car. Luckily they lived. There wasn't a hint of warning.
I hope this helps,
Best Regards and good luck with this.
Mark

Posted on Feb 21, 2011

early93
  • 177 Answers

SOURCE: Constantly having to replace front

Let me guess, you have a superduty that has a lift kit and big wheels and tires on the stock hubs. This is a no no. When the bigger wheels and tires are installed, there is an offset that moves the wheels out away from the truck. This puts a lot of stress on the hub assembly. I saw a kit for this on tv the other day. I think it's made by raybestos. It converts the truck over to the older style spindle and hub assembly. This will allow you to service the bearings. But the main advantage is that you won't be going through bearings. Just look around online and see if you can find anything about this.

Posted on Aug 04, 2011

  • 1212 Answers

SOURCE: Are the bushings in rear knuckle of 95 eclipse

Yes, but not always cost effective. Some performance aftermarket companies have them available, and Ebay is as good as any source for locating them.

Posted on Jan 16, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair vw


Lift Vehicle and place on axle stands. Remove wheels. Disconnect the lower control arm from the bolts that hold the ball joint, or from the knuckle. Undo the rear two bolts that hold the ''D'' shaped rear bush and the bolt that holds the forward bush. Have it pressed out and replace with new one. Reverse the procedure for installation. While the arm is out check the condition of the ball joints and replace if needed. After assembly have the front wheel alignment checked.

Jul 04, 2014 | 1995 Volkswagen Polo 1.6

2 Answers

Why my rear wheel is not straight like the front wheel.........


this is probably from a failed suspension bush and or spring/ shocky . Have it inspected by an accredited suspension specialist . When done ensure that the rear wheels are properly aligned as their alignment affects the front wheel alignment.

Jun 23, 2014 | 1999 Mitsubishi Galant

1 Answer

My 2004 Ford Explorer is swaying all over the road. The mechanic replaced a rear linkage knuckle and now my steering wheel is crooked. He cannot figure out what the problem is. The bushings look good, But...


Can i ask for more details? Such as when you drive down the road and take your foot off the gas pedal does the truck begin to sway?
Does it sway when you press the gas pedal only?
If it sways when you are releasing the gas pedal its probably rear bushings. Worn bushings can cause your vehicle to sway quite a bit.

Jan 02, 2014 | Ford Cars & Trucks

1 Answer

Rear knuckle bearing needs replacing


bushing or bearing? bearing remove rotor and connector and unbolt.
bushing in rear are usually replace component

Dec 06, 2013 | 1995 Cadillac DeVille

1 Answer

Replacing bushings for the rear on a 2004 cadillac cts 3.6L


The howling is more likely rear hub
bearings- in wheel knuckle assy

Check for differential axle seal leaks
& check fluid level before that goes bad

I have a 2004 Lincoln LS with similar rear
drive & no problems with dry rot & it sits outside

Replace the worn parts

Try Rock Auto.Com & try for Moog Parts

The Stabilizer Links are shot for sure front & back

Mar 06, 2013 | Cadillac CTS Cars & Trucks

1 Answer

2001 Aztek rear brakes thunking noise.


rear sway bar link pins and bushings

Oct 18, 2012 | 2001 Pontiac Aztek

2 Answers

Are the bushings in rear knuckle of 95 eclipse replaceable


Yes, but not always cost effective. Some performance aftermarket companies have them available, and Ebay is as good as any source for locating them.

Jan 16, 2012 | 1995 Mitsubishi Eclipse

1 Answer

Need to know how to replace lower control arm


LOWER CONTROL ARM

REMOVAL
1) Raise and support vehicle. 3) Remove the steering knuckle.
Remove the bolts fastening the power steering cooler to the front suspension cradle crossmember reinforcement (Fig. 21). 5) Remove the lower control arm rear bushing retainer bolts located on each side of each lower control arm rear bushing. NOTE: The bolts fastening the cradle crossmember reinforcement are of three different thread sizes. Note the location of the various sizes.

6) Remove the bolts attaching the cradle crossmember reinforcement to the front suspension cradle crossmember (Fig. 22). Remove the 2 bolts fastening the reinforcement and rear of cradle crossmember to the body of the vehicle. Remove the reinforcement. 7) Remove the pivot bolt attaching the front bushing of the lower control arm to the front suspension cradle crossmember. 8) Remove the lower control arm.

Sep 25, 2009 | 2006 Dodge Caravan

1 Answer

How do you replace a rear passenger side torison bar on an oldsmoblie alero 1999


SAFELY RAISE AND SUPPORT REAR OF CAR ON JACK STANDS. REMOVE THE TORSION BAR TO KNUCKLE BOLT WASHER AND BUSHING.REMOVE TORSION BAR TO CHASSIS BOLT.REMOVE BAR FROM THE CHASSIS.TO INSTALL.INSTALL TORSION BAR TO THE CHASSIS TORQUE THE NUT / BOLT TO 48 FT LBS.PLUS ADDITIONAL 120 DEGREE TURN.TORSION BAR TO THE KNUCKLE TORQUE THE BOLT TO 51 FT LBS.

Sep 24, 2009 | 1999 Oldsmobile Alero

1 Answer

2002 Pontiac Aztek - AWD disable light and Anti Lock Light


AWD disabled from a sensor unit in rear differential that senses high temp. This thing is over $300. Whine is from fluid. Need to change fluid. This versatrack fluid is about $40 per bottle and you need 3 bottles. Thumping noise is from loose rear knuckle bushings. These are part of the entire rear knuckle assy. and you must replace complete knuckle.

Jun 22, 2009 | 2002 Pontiac Aztek

Not finding what you are looking for?
2005 Mitsubishi Endeavor Logo

Related Topics:

694 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...