Question about Chevrolet 3500

2 Answers

Reverse lites didnt work/put on new prindle switch/now trying to trace wire from switch to lites /could not locate/were do i go from here

Posted by on

  • SPINDLEY Oct 04, 2010

    2004 CHEVY DURAMAX/IZUZU vin#1GBJC33214F235606 ALLISON TRANS 6.6liters
    I AM RUNNIN OUT OF TIME HERE.ILL BE BACK IN THE MORN. OR LATER TONITE.IF YOU CAN GIVE ME A WIRING DIAGRAM I WOULD APPRECIATE IT.IF NOT THATS OK.THANKS MAN

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,796 Answers

Hi!!
I have a couple of diagrams that I could not sent you because this site only allows images of 150k or less. Please provide an email address to send them to. And I also have a question, your vehicle is a 04 chevy 2500HD with a 6.6 L engine??
Basically all the back up lights work the same, when the shift selector is put in reverse, back up switch sends the signal to the back up lights. So all the back up wiring diagrams are similar.

Posted on Oct 05, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

The right location of the Back-Up Light sensor is refer directly at the year and model of the vehicle; send us details about your year and modet to look it.

If you changed the fuses and bulbs and still nothing, its the reverse switch thats on the tranny. First try it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it.

Keep in touch.

Posted on Oct 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locating wiring for reverse


the easy way is to tap into the reverse rear white tail light wiring RUDY PEREZ.

Oct 10, 2014 | Cars & Trucks

1 Answer

98 jeep cherokee sport reverse lights have no power


lamps good,
fuses good. in fuse boxes.
so the reverse switch is bad.?
on the A/t car this switch is called the PRNDL switch prindle.
if the R contact goes bad (as the all do) the lamps go dead.

Mar 01, 2014 | 1997 Jeep Grand Cherokee

1 Answer

Backup lights out bulbs ok


its just 2 parts , not counting wires, fuse or dead battery.
car runs? Head lights work? at same time?

the switch is bad.
or the bulbs are bad.
the A/T car (auto not stick)
the PRNDL prindle switch does this.
did you try wiggle the lever in REV. with person 2 behind you watching.
did the lamps flash,? bingo bad PRNDL.

with a Volt meter, any (1920 to now) you check the voltage
at the PRNDL, , 12v in , and
0v out , in reverse is bad switch.
1-10v out is a short in the line, (less that 11volts is a short)
12v out is good, your lamps are bad, unplugged . or cut.
top hard fail here is some hack job (uhaul infamous) cut the wires all
up and used wire nuts (illegal on cars) an fails hard.

Dec 22, 2013 | 1997 Toyota Camry

1 Answer

Reverse lights stuck on 2002 acura tls


the reverse light switch is broken.
we call this switch on A/T tranny, the PRNDL, "Prindle"
its stuck at R
or is trailer hitch wiring from H3LL. (just a glance there and .....)

on M/T tranny car is called the REverse switch. a single switch and vastly cheaper.

Sep 22, 2013 | 2002 Acura 3.2TL

1 Answer

Why my shifter indicator is not coming on?


if no shift indicatorthen it might be a cluster issue. Try replacing the cluster or have the dealer reprogram it for you. The shift indicator is a part of the wiring harness associated with the 'Prindle switch' on the driver's side of the transmission. If the wiring harness is fine and the cluster is reprogrammed and the issue still exists, then just replace the Prindle Switch. When removing the wires, make sure to heat up the wiring harness plugs with a lighter for about 10 seconds before trying to pull it out. The connectors come from the factory with this sticky sealant stuff that is like glue when it is cold...

Mar 31, 2011 | 2000 GMC New Sierra 1500

1 Answer

Neutralswitch location


switch is part of gear range selector position switch known as prindle switch. it is located on transmission drivers side and has two square connectors. one is a four wire connector, other is eight wire connector the shift cable lever need to be removed to replace it.

Feb 10, 2011 | 2004 GMC Envoy

3 Answers

Reverse light do not work


Check the fuse and bulbs, I f they are OK then maybe your backup switch is bad which should be located on your transmission. Good luck

Dec 19, 2010 | 1993 Toyota Corolla

1 Answer

When you turn on headlight switch, the running lights come on but not the headlights. I have the lights hooked up on a toggle switch and they work fine that way. I have tried changing out the headlight...


have you checked your dimmer sw, sometimes this is it...did the hd lite problem show up when you put the toggle on, if so look for a ground....also trace the red wire from the head lites to a junction where the lites get their voltage....good luck

Feb 26, 2010 | 2003 Jeep Wrangler

1 Answer

INSTALLING BACKUP CAMERA ON BUICK RENDEVOUS


ASE Mechanic:
with out any schematics you can trace these wires down by finding the reverse lights, and disconnecting the bulb and installing a test light, and with a buddy put in reverse while you check to see which wire gets hot!!!!!!!!!!!!!!!!!

Jan 17, 2009 | 2005 Buick Rendezvous

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...