Question about 2003 GMC Envoy

1 Answer

The cover for the center consul came off. Seems like a simple fix. However, when I hook it back up, the lid will not close properly. Is there a diagram or something available I can look at?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • GMC Master
  • 1,051 Answers

Go to the autozone web site www.autozone.com and register for free. The free registration gives you free access to dozens of online manuals which include diagrams.

Posted on Oct 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Nissan sentra trunk won't close - like the latch isn't hitting hook.


It is common if you have loaded anything heavy into or out of the trunk, it is easy to catch on the latch and it bends quite easily. Try covering the catch or latch with a grease like white lithium or vaseline and shutting the trunk lid down lightly and see if you can see the imprint of where it is striking, then bend accordingly. Or you can climb into the trunk with a flashlight and shut it down and see if you can see which way it needs to be bent to line back up.

Jul 07, 2015 | 2010 Nissan Sentra 2.5

1 Answer

How to disconnect the 12 volt receptical in center console?


need to disconnect the feed wire back one connection block from plugin, you should be able to find its wires running up from under dash end of consul. or you can pull all the screws and remove the consul. to get at the wires to follow them back to the first connector.

Dec 14, 2014 | 2006 Chrysler PT Cruiser

1 Answer

HOW TO REMOVE CENTER CONSOLE 2001 NISSAN SENTRA SE


slid both seats fowrad as far as they will go and there are 2 srews on the bottom of the rear of the center consule and then slide the seats all the way back and ther should be a small piece of platsic that looks like it can be removed from underneath the hand brake and then 2 more sres holding the front of the center consule in underneath the plastic piece that goes aROUND THE SHIFTER. if you can send me a pic of the front of the consule if not it should be very easy to figure out uif not what I said in the front of it just discribe it to me.

Jul 11, 2011 | 2001 Nissan Sentra

1 Answer

The trunk lid on my 2000 Avalon vxi seems to be out of alignment (slightly) is this easy to fix? It closes and locks ok, but seems to be sitting high when it's closed


If the lid is too high, the latch / keeper needs adjusting downward -- loosen, move it down, retighten, test -- repeat until proper adjustment is achieved.

Charlie

Jan 06, 2011 | 2007 Toyota Avalon

1 Answer

Hello, where its located the soft top relay in my clk 320 2001. Not opening THANKS!!!!!!!!!! Leo


is your soft top not working it's not the faulty relay, it's control by electronic control unit, it's call soft top control unit, so first do one thing, open boot and have a look, there are one separation lid which is winding like cover, you must have close your boot separation lid buy pulling it out and hang it on hook which is locate both side back in boot, there are two hooks for hookup the separation roller lid,you pull it out and hookup it on two hooks, and close boot then operate roof if still roof not working it's need to be diagnose because there are many sensors and switches are fitted in this system if one switch or sensor not work your roof will not longer be opening and also there are any hydraulic oil leaking or lack of oil in the pump, it will not work, so in this case you must drive your car to the authorized Mercedes workshop who have the right diagnose tool knowledge for this particular car,

Oct 22, 2010 | 2000 Mercedes-Benz CLK

1 Answer

The windows and sun roof doesnt work i think i have a blown fuse


The fuse and relay box on the E30 and E36 models is located in the engine compartment. The E36 models also has relay boxes located under the left side of the dashboard.

Circuit Breakers
Resetting & Replacement

Circuit breakers are located inside the fuse panel. They are automatically reset when the problem corrects itself, is repaired, or the circuit cools down to allow operation again.

One of the less known about fuses that can cause all this to go out is the fuseable link. It is in a black plastic box near the battery. It is an appx 60A thin metal strip fuse. Check the website link to the right for more info.

Also, I suggest check your Fuse Diagram in the BMW 525i Owners Manual here.

Power Sunroof
Emergency Closure Operation

The sunroof is equipped with an emergency closure feature should the sunroof motor fail or the vehicle has lost electrical power. To close the sunroof under these conditions:
  1. Remove the front headliner trim panel.
  2. Using the 6mm hex key that is included with the tool kit, insert the key into the hex socket and turn the socket to close the sunroof.
2ad9520.jpg

Fig. Remove the trim panel to access the sunroof motor

db812a0.jpg

Fig. Insert the 6mm hex tool from the tool kit and turn the hex socket to close the sunroof


Removal & Installation
E30 Models

f5f1bc5.jpg

Fig. Sunroof components-E30 3 Series shown, E36 similar

c5ff2b7.jpg


Fig. Sunroof lid retainer clip location-E30 3 Series shown, E36 similar
  1. Open the sunroof lid 2-4 inches (5-10cm).
  2. Unclip the roof liner frame and push back into the opening.
  3. Close the sunroof lid and loosen the screws on each end of the gates.
  4. Pull in the retainers, remove the center screws and lift off the lid.
  5. Remove the cover over the motor and gearbox. Close the sunroof lid, if not already closed.
  6. Disconnect the wiring harness and remove the 3 mounting screws. Remove the motor and gearbox.
  7. Push the cables back evenly on both sides. Remove the rail covers and pull the cables out of the guides.
  8. Place the cable in the center position of the gate and press off.
To install:
  1. Install the cables to the gate. The cable are marked with the proper side of installation. Do not lubricate fabric covered cables.
  2. Pull the cables through guides and align the cables. Insert a hex key through the gate and cable at the 0 position.
  3. Install the motor and gearbox. The motor and gearbox must be synchronized with the hole in the drivegear aligned between the centers of the 2 gears. Torque the bolts to 2.0 ft. lbs. (2.8 Nm).
  4. Install the sunroof lid. Use new screws and torque to 2.5 ft. lbs. (3.5 Nm).
  5. Adjust the sunroof lid. Pull the roof liner frame into position and clip into place.

E36 Models
  1. Close the sunroof fully. With a quick actuation of the sunroof opening button, open the sunroof so the back edge of the lid depresses 0.08-0.12 inches (2-3mm).
  2. Slowly push the roof liner panel back into the roof. Do not force or use a quick motion or damage could occur.
  3. Remove the mounting screws and pull the lid off at the rear side. Do not operate the sunroof with the panel removed.
To install:
  1. Install the lid and check that the hooks and levers align. Install the screws with threadlocker or use new micro-encapsulated screws. Torque to 2.5 ft. lbs. (3.5 Nm).
  2. Adjust the sunroof lid. Lower the rear of the lid by operating the motor. Pull the liner forward and clip into place.

Good luck.

Mar 15, 2010 | BMW 525 Cars & Trucks

4 Answers

Toyota Camry center console auxillary box won't open


quite easy in fact just grab the plastic behind the control box and pull straight up the plastic will detach easily lift it up a little bit and you can now slide your fingers behind the lid cover.
5_17_2015_3_05_56_pm.jpg

Oct 27, 2009 | 2008 Toyota Camry

2 Answers

How do I replace the battery and where is it located?


Procedure:

Remove battery cover located under the hood on the passenger side in the back. Simply pry the plastic catch in the front, open it like a lid and jiggle it loose and set it aside.
Use the small flat screwdriver to pop up the center peg in the five peripheral fasteners holding down the plastic compartment cover that you just removed the battery cover from. Each of these has a small black plastic circular flat topped center peg inside a larger plastic circular disk which has 4 slots under which you can slide the screwdriver to pop up the center peg. When the peg pops up simply slide the screwdriver under the larger disk to remove the assembly and loosen that site of fixation. When all five fasteners are out you can remove the entire compartment cover.
The battery terminals are removed with the 10mm wrench
The black box in front of the battery can be lifted out of the way by pressing on the plastic catch in the front of the box to loosen it from the metal flange that it is attached to.
The metal battery holder is removed with the 10 mm wrench. The nut is removed and the long bolt is slid out of the holder and then unhooked from it's bottom anchor. Jiggle the metal bar over the top of the battery to unhook the back hook from its bottom anchor. It may be necessary to lift the plastic over the back of the battery gently and lift out the soft clear plastic washer fluid tube from its guides to get at the back hook.
Gently lift the battery out while holding the cables out of the way.
Tools required:
10mm wrench, small flat screwdriver
Procedure:
Remove battery cover located under the hood on the passenger side in the back. Simply pry the plastic catch in the front, open it like a lid and jiggle it loose and set it aside.
Use the small flat screwdriver to pop up the center peg in the five peripheral fasteners holding down the plastic compartment cover that you just removed the battery cover from. Each of these has a small black plastic circular flat topped center peg inside a larger plastic circular disk which has 4 slots under which you can slide the screwdriver to pop up the center peg. When the peg pops up simply slide the screwdriver under the larger disk to remove the assembly and loosen that site of fixation. When all five fasteners are out you can remove the entire compartment cover.
The battery terminals are removed with the 10mm wrench
The black box in front of the battery can be lifted out of the way by pressing on the plastic catch in the front of the box to loosen it from the metal flange that it is attached to.
The metal battery holder is removed with the 10 mm wrench. The nut is removed and the long bolt is slid out of the holder and then unhooked from it's bottom anchor. Jiggle the metal bar over the top of the battery to unhook the back hook from its bottom anchor. It may be necessary to lift the plastic over the back of the battery gently and lift out the soft clear plastic washer fluid tube from its guides to get at the back hook.
Gently lift the battery out while holding the cables out of the way.
Tools required:
10mm wrench, small flat screwdriver
Procedure:
Remove battery cover located under the hood on the passenger side in the back. Simply pry the plastic catch in the front, open it like a lid and jiggle it loose and set it aside.
Use the small flat screwdriver to pop up the center peg in the five peripheral fasteners holding down the plastic compartment cover that you just removed the battery cover from. Each of these has a small black plastic circular flat topped center peg inside a larger plastic circular disk which has 4 slots under which you can slide the screwdriver to pop up the center peg. When the peg pops up simply slide the screwdriver under the larger disk to remove the assembly and loosen that site of fixation. When all five fasteners are out you can remove the entire compartment cover.
The battery terminals are removed with the 10mm wrench
The black box in front of the battery can be lifted out of the way by pressing on the plastic catch in the front of the box to loosen it from the metal flange that it is attached to.
The metal battery holder is removed with the 10 mm wrench. The nut is removed and the long bolt is slid out of the holder and then unhooked from it's bottom anchor. Jiggle the metal bar over the top of the battery to unhook the back hook from its bottom anchor. It may be necessary to lift the plastic over the back of the battery gently and lift out the soft clear plastic washer fluid tube from its guides to get at the back hook.
Gently lift the battery out while holding the cables out of the way.
Tools required:
10mm wrench, small flat screwdriver
Procedure:
Remove battery cover located under the hood on the passenger side in the back. Simply pry the plastic catch in the front, open it like a lid and jiggle it loose and set it aside.
Use the small flat screwdriver to pop up the center peg in the five peripheral fasteners holding down the plastic compartment cover that you just removed the battery cover from. Each of these has a small black plastic circular flat topped center peg inside a larger plastic circular disk which has 4 slots under which you can slide the screwdriver to pop up the center peg. When the peg pops up simply slide the screwdriver under the larger disk to remove the assembly and loosen that site of fixation. When all five fasteners are out you can remove the entire compartment cover.
The battery terminals are removed with the 10mm wrench
The black box in front of the battery can be lifted out of the way by pressing on the plastic catch in the front of the box to loosen it from the metal flange that it is attached to.
The metal battery holder is removed with the 10 mm wrench. The nut is removed and the long bolt is slid out of the holder and then unhooked from it's bottom anchor. Jiggle the metal bar over the top of the battery to unhook the back hook from its bottom anchor. It may be necessary to lift the plastic over the back of the battery gently and lift out the soft clear plastic washer fluid tube from its guides to get at the back hook.
Gently lift the battery out while holding the cables out of the way.

Apr 17, 2009 | 2004 Nissan 350Z

1 Answer

Convertible Top Lid Not Closing


top still needs to be adjusted to fully seat properly in the trunk/boot. if the upholsterer who replaced the top is not familiar with the adjusting process for a BMW, then i would take it to a BMW dealer and have them do the final adjustments.

Mar 13, 2009 | 2001 BMW 330

Not finding what you are looking for?
2003 GMC Envoy Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...