Question about 1995 Dodge Intrepid

1 Answer

On a 95 dodge intrepid the back drivers side thers a bar that connects to the wheel it runs like to the drivers back door what is it called not an axel

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 71 Answers

Control arm

Posted on Oct 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Intrepid will not start. 2.7 engine. There is no sound at all. I do not hear the fuel pump prime, ther are no dash lights except for the door open and odometer, no wipers, no power to radio( after...


check your fuel pump relay, and the fuses, and other relays, they are normally, located in a black box on the drivers side , under the hood on your car.

May 11, 2011 | 1999 Dodge Intrepid

1 Answer

How to replace a sway bar end links to a 94 intrepid



REMOVAL & INSTALLATION

The rear suspension on LH platform vehicles is a fully independent suspension. A stabilizer bar (also called a sway bar) is mounted in rubber isolator bushings and connects the rear struts through links. Note that the fuel tank must be removed to remove the stabilizer bar.

CAUTION OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Disconnect the negative battery cable. Relieve the fuel system pressure.
  2. Raise and safely support the vehicle.
  3. Remove both rear wheels.

  1. Position a transmission jack under the fuel tank just forward of the crossmember to help support the fuel tank when crossmember is removed.
  2. Remove the four crossmember to frame rail attaching bolts. Remove the fuel tank.
  3. Remove the stabilizer bar to link assembly attaching nuts and remove the bar and isolator bushings as an assembly from the vehicle. Inspect the isolator bushings for damage or excessive wear and replace, if necessary.

To install:
  1. Inspect for broken or distorted retainers and bushings. If bushing replacement is required, replacement bushings can be installed by locating the split in the bushing, prying open and removing the defective bushing from around the stabilizer bar.
  2. Install the stabilizer bar and isolator bushings back into the vehicle as an assembly making sure bar is centered in vehicle so it doesn't contact other suspension components.
  3. Install stabilizer bar attaching link onto stabilizer bar. Install new link to bar attaching nuts and tighten to 70 ft. lbs. (95 Nm).

Replace the sway bar bracket bolt with new after loosening or removing them. Only use original equipment bolts as replacements.
  1. Install the fuel tank back onto the vehicle.
  2. Position the crossmember on frame rails and install four mounting bolts. Tighten attaching bolts to 70 ft. lbs. (95 Nm).
  3. Remove transmission jack from under the fuel tank.
  4. Install the rear wheels and lug nuts. Tighten the lug nuts, in a star pattern sequence, to 95-100 ft. lbs. (129-135 Nm).
  5. Lower the vehicle. Reconnect the negative battery cable.
  6. Pressurize the fuel system and check for leaks.
  7. Check and reset the rear wheel toe to specifications as required.

Jul 03, 2010 | 1994 Dodge Intrepid

1 Answer

Have no fuel pressure. Is there a rollover safety switch on the 95 Dodge Intrepid?


NO THERS NO RESET.. IF FUEL PUMP IS NOT COMING ON THEN YOU WILL NEED TO REPLACE THE FUEL PUMP...

May 02, 2010 | 1995 Dodge Intrepid

1 Answer

How do i bypass security on intrepid


You need a 680 ohm resistor. one side connect to ground the other side connect to the light green with orange wire in drivers door harness

Nov 28, 2009 | 2001 Dodge Intrepid

1 Answer

Where is ther starter located on a 95 dodge intrepid


under the car by the battery. to replace-remove wheel well cover on front river tire

Oct 17, 2009 | 1995 Dodge Intrepid

1 Answer

How do I remove the drivers side door panel on a 2004 Dodge Intrepid


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

May 29, 2009 | 2004 Dodge Intrepid

1 Answer

Finding flasher on 95 dodge intrepid


The flasher relay should be located in the fuse panel on the left end of dasboard which is visible with driver door open and there you will see a panel to remove to gain access.

Mar 17, 2009 | 1995 Dodge Intrepid

1 Answer

I have a 1999 dodge intreped. All windows excpect


I HAVE A 98 INTREPID AND I WENT TO A JUNK YARD AND JUST PULLED THE PASSENGER SWITCH OUT OF THE DOOR AND UNHOOK.WIRES....VERY EASY....PUT IN YOUR CAR AND THAT SHOULD WORK...ITS PRYS OUT OR PULL OUT WITH PLYERS....THESE SWITCHES CONNECT LIKE A CIRCUIT AND IF PASSENGER DOOR SWITCH IS BAD IT WILL NOT WORK FROM DRIVERS OR PASSENGER SIDE...98 TO 2000 ARE ALL THE SAME PARTS....HOPE THIS HELPS.....

Mar 05, 2009 | 1999 Dodge Intrepid

1 Answer

Anti-theft problem 95 dodge intrepid


you half to call a dodge dealer

Jan 05, 2009 | 1995 Dodge Intrepid

1 Answer

Dodge Intrepid - how to secure Cover around battery?


Hi,

Dodge Intrepids are not very common in my country. If I remember right, the battery holder/bracket is very exact. It is possible that the new battery is slightly wide/longer and therefore would not be sitting squarely. If this is the case, then the clamp/cover would not fit rightly and would be misaligned. Pls correct me if I am wrong, your car has the battery on the wheel well driver's side front tire? The battery slightly bigger, either that or you need to redo the battery placement all over again.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Sep 03, 2008 | 1995 Dodge Intrepid

Not finding what you are looking for?
1995 Dodge Intrepid Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...