Question about 2001 Ford Taurus

1 Answer

What kind of pully do I need to remove a hymolic balance?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

It's called a harmonic balancer puller. A lot of the chain auto stores will load them for free.

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE THE HAMONIC BALANCER AND CRANKSHAFT PULLY.


Could be 24 or 22 mm,what is it car or truck?

Dec 21, 2014 | Cars & Trucks

1 Answer

Crankshaft pully bolt removal


Crank pulley bolt tightens clock wise and loosens counter clock wise. You will need a puller to remove the balance as it has a keyway to hold it on.

Apr 15, 2013 | 1987 Chevrolet Nova

2 Answers

Location of crankshaft censer 2007 chevy cobalt


The Crank shift sensor is located in front of the motor in between the intake manifold and oil filter housing, nest to the knock sensor. Look on side cylinder block beside starter.you have to remove the starter to remove the crankshaft sensor. Hope this helps. Thanks for choosing Fixya, RJ

May 16, 2011 | 2007 Chevrolet Cobalt Coupe

1 Answer

Where is the crank sensor located on a 07 chevy uplander


the crankshaft postion sensor is always located either under the harmonic balancer pully aka crankshaft pully or mounted right outside the pully if yoiu need to change it keep in mind that you will need to to own or rent a harmonic balancer pully puller and a harmonic balancer pully installer kit both you can rent both at autozone fairly cheap and get all your money back when your done
job rating from 1-10 about a 3


hope it helps if so could you please leave me a 4 thumbs up feedback thank

May 12, 2011 | 2007 Chevrolet Uplander

3 Answers

Pully disconnected from harmonic balancer. Trying


thats a hard bolt to break lose almost takes the sudden **** u get for a impact.i had to use a guy bigger then superman to break it free for me

Oct 04, 2009 | 2000 Lexus SC

1 Answer

V belt broke rapped around crank pully broke sencer wont crank


The crank balancer pulley needs to be removed so the crank sensor can be replaced. You will need an air impact wrench to remove the pulley bolt and a puller to remove the balancer.

Sep 24, 2009 | 1993 Buick Regal

1 Answer

How do i replace the harmonic balancer on a 95 royale 88


Remove all belts and rad, use a pully puller to remove the belt pully, and then you need a special puller to pull the harmonic balancer.

Aug 12, 2009 | Oldsmobile 88 Cars & Trucks

1 Answer

Hoe do you remove the harmmce balancer


you need a balancer puller or a pully puller.most any parts store should have what you need. hope i helped..

Jul 06, 2009 | 1983 Ford Ranger

1 Answer

HELP remove balancer pully


once you get the bolt out you need a harmonic balancer puller

Jun 05, 2009 | 1990 Buick Riviera

1 Answer

Pulling the harmonic balancer off a 98 nissan pathfinder


Most balancers have two parts, the inner crankshaft section is where the huge bolt is and holds it to the crankshaft, they may also be a few smaller bolts around the outside of the big bolt, those hold the belt pulley on to the crankshaft. If it thats kind of setup remove the small bolts and the pulley should come off, you may need to use a wooden hammer etc to get it loose once the bolts are out.

Mar 11, 2009 | 1998 Nissan Pathfinder

Not finding what you are looking for?
2001 Ford Taurus Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5677 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...