Have 2005 Mercury Monterey with power front seats. Front Driver seat goes back but stopped going forward. Is it a fuse problem. I can see several fuses under the seat . Thanks, Dan

SOURCE: Power driver seat will not adjust forward or back.

My intuition tells me that the 6 way power seat track forward / reverse motor is bad. Sometimes you can replace just the one motor but most often a whole new power seat track is the only way to repair. It is not too bad to replace but the seat will have to be removed from the car and placed upside down to access the track assy. There are 2 bolts in the front of the seat and 2 bolts in the back of the seat that hold it down to the floorboard. Once it is loose you can rock the seat backwards to access and unplug the electrical connectors.

SOURCE: 2005 Mercury Monterey van - fuse location

Hello Kevin I hope I can help you find this fuse and fix this for you.The fuse location number should be 63 it should be a 30 amp fuse.I don't know if your manual will show you this location but I do hope it does.But if not I'll do my best to try and help you find it.In your fuse box look about middle ways in it.I hope you see a line of the standard small size plug-in fuse's a row or 4, just below those should be a row of 2, the row of 2 is what your looking for fuse number 63 is the one on the left if your looking straight at the fuse box, or the one on the driver,s side it should have 30 amp on it.Check that fuse or just replace it.I hope that was helpful Tim

SOURCE: I want to make my 1999 Mercury Villager Sport into

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

SOURCE: 50 amp fuse keeps blowing

There are several ways to solve this problem. You need a schematic of vehicle from Haynes or whoever, such high amperage I would place in line fuses to each item, that way it will isolate problem then look for bare or rubbing wire under seat or in doors ( too much junk jammed under seats) ? Anyway with a little time and some disassembly should be a simple fix.

SOURCE: 2005 DB9 electric seat problem

you have to re set the system
one by one seat & windows
1st start with the driver seat move it all the way forward and all the way up and the back as will all the way forward than to the back all of them one by one
do the same to other seat it will work
and the windows as will
close the door take the window up and hold till you hear a sound and down and hold till you hear the sound .