Question about 2004 Mitsubishi Endeavor

1 Answer

Passenger headlight on 2004 Mitsubishi Endeavor low beam did work. Replaced with new light bulb and now low and high beam dont work. Drivers side work fine. Any ideas

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 4,535 Answers

Make sure its the correc bulb--chec over the connection and look inside lite-maybe new but broken

Posted on Oct 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

2 Answers

Head light have low but when using high does not work just on one side drivers side


HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

Dec 20, 2015 | 2004 Nissan Sentra

3 Answers

One low beam head lights will not work, high beam works though


check for a damaged wire for the low beam. Also wouldn't hurt to check the ground wire as the high beam will try and ground through the low beam but not visa verse

Dec 29, 2013 | 1997 Chevrolet Blazer

1 Answer

I put in a new headlight bulb in the drivers side in but i dont have low beams but high beams work what is the problem?


Usually the low beam light of the bulb burns out first, so this new bulb is acting like it is defective. If the passenger side bulb is working for both low and high beams you could test this new bulb on that side to be sure. If it works OK on this side there may be a problem with the connector wiring on the driver side.

Nov 24, 2013 | Cars & Trucks

1 Answer

Passenger headlights only do not operate.


check the bulbs first and also the fuses theres a fuse for each side and for low and high beams, start there, good luck.

Feb 19, 2010 | 2002 Mitsubishi Eclipse Spyder

1 Answer

My passenger side low beam headlight is out. the driver side low beam headlight works fine. I replaced the bulb and the headlight still doesn't work. What should I look at next?


Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block

Dec 16, 2009 | 2004 Hyundai Santa Fe

1 Answer

How do you adjust the headlights on a 2004 endeavor


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 12, 2009 | 2004 Mitsubishi Endeavor

1 Answer

Low beam not work !!


replace the headlight bulbs. Usually when the bulbs blow out the low beam blows out first, but the high beams still work. If you want and need both low and high beams to work then replace the headlight bulbs with brand new ones and I garauntee that both low and high beams will work

Mar 27, 2009 | 1999 Dodge Caravan

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...