Question about 2000 Dodge Caravan

1 Answer

The belt is riding off the tension pully. - 2000 Dodge Caravan

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Relace the tensioner they are phenominal about going bad

Posted on Oct 04, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My serpentine belt has fallen off my 1991 chrysler lebaron 6cyl a number of times with no cause that is obvious to me. Any suggestions on how I prevent this in the future?

Most likely the belt tensioner but very common for the belt to be mis-routed even when it looks right. Back side idler, if applicable, also could be the culprit. Like other posted reply, check the belt tension with finger or thumb as well.

Aug 28, 2011 | Chrysler LeBaron Cars & Trucks

1 Answer

I have a 1999 chevy blazer with a 4.3 in it. i put a new belt tensioner and a new belt on it. everytime i put a new belt on its quiet for a while but then eventually it starts squealiong once it gets...

no ajustment...spring loaded.... but need to check all the pullys with the belt off a lot of the time it is a idler pully making it ride wrong but not far enough to throw belt off....hope it helps

Nov 25, 2010 | 1999 Chevrolet Blazer

1 Answer

The belt rides of the tension pully. Why? the pullies are not all in line. Is there a spring inside the tension pully & how do I get at it?

regardless of the v6 engine u have the belt tenioners r phenominal about going bad in mostly 2 ways one way is not retracting or bouncing back and second is they dont stay aligned when it is pulled down from excellerating and it throws the belt.

Oct 04, 2010 | 2000 Dodge Caravan

1 Answer

Want to fit fan belt cant find the proper way

You have to find the tension pully. using a 3/8 socket wrench. not the socke but the actual wrench. place the square end of the wrench into the notch on the pully and either push or pull (depends on the v-belt system) and it should move. place your v-belt around the pully's according to the diagram under your hood leaving your tension pully to be the last one the belt goes on. Move that tension pully as mentioned above and place it the belt on the pully. The diagram under the hood should also show you where that tension pully is located.

Oct 04, 2010 | Ford Fusion Cars & Trucks

1 Answer

The serpentine belt seems missaligned as it goes from the crank pully over the tentioner and down to the power stearing pully. the belt ride the tentioner towards the outside.

The tensioners have always been a problem on the mini vans,if everything else that the belt rides on looks good then its probably the tensioner

Sep 07, 2010 | 1993 Dodge Caravan

1 Answer

My belt just came off my battery light is on and my coolant light is on one of my pullys is loose how do i know if this is water pump pully or tensioner pully

The tensioner pulley is smaller than all the others with a smooth riding surface. Please rate me on this answer.

Jun 08, 2010 | 2002 Saturn Sl

1 Answer

Need to know how to put a serpentine belt on a 1995 302 ford motor

Below the altenator is a tensioning pully, insert a 3/8" ratchet or breaker bar in the square hole on the tensioner and release the tension on the surpentine belt and remove the belt. Route the new surpentine belt in place up to the altenator and take the tension off the tensioner and put the belt over the altenator pully. Double check to make sure the belt is riding correctly on all the pullies before starting. Crank the engine over several times before starting to seat the belt. f78f558.jpg

Jun 02, 2010 | 1995 Ford Mustang

1 Answer

Ho0w do you replace the power steering belt on 1996 dodge avenger

there should be a tension idler that has to be retracted to give the belt slack most has a 1/2 inch square hole in it for a break over bar to fit in it to realese tension however i have not delt with this particular model but most are the same also be sure to carefully look at how the belt pattern is or if it still has the sticker for belt routing on it realese the tension and slip belt off first pully making sure not to put yoru finger between the belt and the pully after the first pully has been cleared the the tensioner can be released and the belt removed then put new belt on all pullys but one at this point tensioner bust be realesed again ultill belt is plased on last pully be suer belt is inline with all pullys

Mar 27, 2010 | 1996 Dodge Avenger

1 Answer

How do I replace belts on a 4 cyl 93 bmw 318is. My biggest problem is finding out how to release the tension.

Most later model cars have a belt tensioner. Look for a wheel or pully that the belt rides over. You will see a place to put a ratchet or breaker bar. Pull back on the tensioner and it will allow you to slip the belt out for replacement.

Jul 16, 2008 | BMW 318 Cars & Trucks

Not finding what you are looking for?
2000 Dodge Caravan Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides