Question about Volkswagen Polo

1 Answer

I have a 2002 vw polo 1.2 3cyl.AWY engine has it got a cam belt or timing chain Many thanks Mark

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Hi mark,to answer your question,if you look at the very front of the engine you will see some pulleys for the waterpump/pwr steering/alt.just behind you will see a 1.1/2 plastic cover that hides the BELT.(engine designed by Hyundai in collaberation with VW for the far eastern market(China)same block also used for 3cyl diesel.
regards,geoff.

Posted on Oct 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Does the 2014 VW Polo 1400 have a timing belt or a timing chain?


The 2014 VW Polo 1400 has a timing belt, Cheers,
Dan

Oct 08, 2015 | Cars & Trucks

1 Answer

Camshaft sensor location


It's on the front of the cam shaft near the timing chain. You have to open the camshaft cover to access it.

Feb 21, 2014 | Cars & Trucks

1 Answer

I need a picture of the timing marks for Jeep 4.0


Timing the Cam to the Crank

There are several ways to time the cam to the crank. Be sure to check the manual before you install the timing chain or belt.

  • Some timing sprockets are properly timed when the marks face each other.
  • On others, there must be a certain number of chain links between the marks.
  • Sometimes chains have colored links that must be aligned with the marks on the sprockets.
  • Some overhead cams have a mark on the cam gear that lines up with a mark on the cylinder head when the timing mark on the damper is at the TDC mark.
Align the timing marks for the camshaft and crankshaft sprockets before removing the timing belt or chain.

If the old parts are available, carefully compare the new gears or sprockets with the old ones. Check the keyway and timing marks just in case there might have been an error made in manufacturing. Sprockets are sometimes stamped backward. Its much better to find the problem during assembly, rather than waiting until problems show up after reassembly and reinstallation.

Maintaining Valve Timing

During a valve job, it is essential to keep the timing chain or belt in place to maintain correct valve timing. Position the number one cylinder at TDC. Some overhead cam engines use a single long chain for a cam drive. The chain can be wedged against its guides with a tapered block of wood.
the chain tensioner on some ohc engines must be wedged to keep the chain in position during cylinder head removal. courtesy of nissan motors.

Some engines have a lower and upper chain. These engines do not require special attention to wedging the chain. Be sure to look for hidden head bolts and check the repair manual before removing the OHC head.

Dec 07, 2012 | 1989 Jeep Cherokee

1 Answer

How do i set the valve timing if i cant see the timing marks on a VW 1.8 20valve golf cylinder head timing chain , i can only find the one on the belt side i have put the cam on TDC for the ex-valve but...


The 2 cams are linked with a chain at the rear of the cylinder head.

The cams need to be set so the slots on the chain sprockets line up with the cam tower caps with 16 links between cam caps.

You cannot see the front crank pulley tdc mark so you need to lock the engine at tdc with a screwdriver jammed into the timing hole on the bell housing after setting engine at tdc or use a DTI
to check to tdc in the #1 spark plug hole.

If the cams have not been disturbed you only need to set the belt cam sprocket to the mark and crank to tdc.....all this means pulling the core support into the service position so the belt tensioner can be locked down and/or doing a complete belt job along with a coolant pump if over 70,000 miles..

Aug 20, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

I need a diagram of timing chain replacement Thank You


During most engine rebuilds, a completely new timing assembly should be installed. If wear exists on any component, replacement of the entire assembly is necessary. Wear in the chain, gears, or sprockets means a timing lag, which results in poor engine performance.
The timing chain or belt is generally installed with the gears in their correct positions. Before installing a new chain, soak it in oil.
OHC (Overhead Cam) Engines
Some OHC engines use a chain drive; others use a belt drive. Removing the cover on some OHC engines that have timing chains is more difficult, because the cover often fits between the oil pan and the cylinder head. There are special procedures for replacing cam timing components in these engines.
Before a chain repair job, perform a leakage test on non-freewheeling engines to check for bent valves, so that an accurate repair estimate can be made.
OHV (Overhead Valve) Pushrod Engines
On many OHV pushrod engines, the crankshaft sprocket is installed on the crankshaft nose and the crankshaft is rotated to position piston #1 at TDC. At this point, a mark stamped onto the crankshaft sprocket is pointing directly upward (toward the camshaft).
The camshaft sprocket is then temporarily bolted to the cam and used to rotate the cam until a mark stamped on the cam sprocket is pointing directly downward (toward the crankshaft). The sprocket is then removed from the cam (without allowing the cam to rotate).
The timing chain is looped over the cam gear, the mark on the cam gear is positioned directly downward, and the chain is looped around the crankshaft sprocket. When the cam sprocket is attached to the cam, the timing marks on the crank and cam sprockets should be pointing toward one another. NOTE THIS IS FOR 2WD 4.0

May 22, 2010 | 2005 Nissan Pathfinder

1 Answer

Oil change and cam belt/timing chain change for volkswagen golf 1.9cc tdi 130 bhp, 1992 model


support engine. remove coolant reservoir. remove serpentine belt. remove serpentine belt tensioner. remove bolts from mount. carefully raise engine up and move mount out of the way.(hard to explain and this is hard to do you have to have the engine in the perfect position and whatnot) remove the top plastic cover. with 19mm socket rotate engine clockwise until hole in cam lines up with hole in head. insert vw special tool to hold cam. remove the 4 6mm bolts on crank pulley. remove plastic covers. with white paint, mark belt to cam and belt to crank. loosen tensioner. remove belt. transfer marks to new belt. strongly suggest replacing water pump. reinstall t-belt. put the tensioner somewhat tight. rotate the engine fully twice. loosen tensioner bolt and adjust to perfect tension using needle and v-groove on adjuster. install is reverse of removal.

Jan 31, 2010 | 2001 Volkswagen Golf

1 Answer

Timing Belt on a 2002 VW POLO


Well it always a chance.Some have pushed over 200 000km.. but recommend every 100 000km to be on the safe side..

Apr 30, 2009 | 1992 Volkswagen Fox

4 Answers

VW Polo Map sensor fault code idling pooly


Hi, I have a 2001 polo 1.4 mpi it lackes power when you hit a hill it just dies, It has had new cat, fuel filter, fuel pump and throttle body, but is still the same it just dose not want to give me full rev's?

Mar 30, 2009 | 2002 Volkswagen Golf

1 Answer

2000 vw passat changed cam belt timed and no diesel coming throug


never had a problem after a belt change, are you sure the crank hasnt moved and if it is the pd engine they need to be bang on or it wont go!! what timing mark did you use for the crank ?

Jan 24, 2009 | 2002 Volkswagen Passat

4 Answers

Polo 1.2 12v does not rev over 3k


hi guys just about to do timing chain on vw polo 1.2 just wondering if any one knows where crank locing pin locates

Jun 30, 2008 | 2002 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

727 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...