Question about 2009 BMW X5

Open Question

E53 2003 X5 Front passenger door locked and unresponsive to remote, use of interior or exterior handle, or use of centre console button

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
onyeredson
  • 404 Answers

SOURCE: Central Locking not working

Hi Craig,
I'm running a E34 Tds Touring with a similar problem, my rear doors and tailgate have dropped of the central locking circuit.
I have been told it is the Central locking Module a large black box under the dash that is faulty, apparently a common problem.
Hope this points you in the right direction,
Please remember to rate my effort!
Paul 'W'
Onyer~EDson(:0) {#><U.K.

Posted on Jan 19, 2009

Ad
Ajkill
  • 2035 Answers

SOURCE: broken exterior door handle,passenger sider ,sliding

Front

  1. Close the front door glass completely.
  2. Disconnect the negative battery cable.
  3. Remove the door screen.
  4. Disconnect the front door lock actuator connector.
  5. Disconnect the rods and the cables.
  6. Remove the screws, and remove the front door lock.
  7. Remove the screws, and remove the front door lock actuator from the front door lock.
  8. To install, reverse removal procedure.
Sliding Door
  1. Close the front door glass completely.
  2. Disconnect the negative battery cable.
  3. Remove the door screen.
  4. Disconnect the sliding door lock actuator connector.
  5. Disconnect the rods and the cables.
  6. Remove the bolts, and remove the sliding door remote controller.
  7. Remove the screws, and remove the sliding door lock actuator from the sliding door remote controller.
  8. To install, reverse removal procedure.

Posted on Jan 26, 2009

  • 3 Answers

SOURCE: 1997 BMW 528i The passenger side front and rear doors won't

I had the same problem on the rear door of my 1998 528i and it was the door actuator that had gone bad. I had to take the rear seat out to get the door panel off. Once I had the door panel off it was not that difficult to replace the door actuator.

Posted on Jul 24, 2009

  • 599 Answers

SOURCE: my key fob won't open the doors on my 03 BMW X5

first check the fuse

Posted on Jul 25, 2009

  • 1986 Answers

SOURCE: door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All my remotes won't unlock passenger doors, why?


this is a problem that can appear after your car battery died, cause the car didn't reset propely, so taking the battery out and putting it back in or letting your car die again would do the trick. I tried a lot of reprogramming procedured for my remote key, none of them worked, what did the trick though was simply unlocking the doors via the all door unlock button on the passenger side door, so simple.

Apr 27, 2012 | Cars & Trucks

1 Answer

Central locking not working on drivers and passenger door


I am having a similar problem with left rear door. I replaced the lock actuator, but it was still not working properly. The trick is getting the door handle in the right spot. The door handle is attached by a cable, and over time the cable is stretched. I used a rubber stopper behind the handle to get it into the exact right position and it worked perfectly.

Dec 31, 2011 | 2003 Land Rover Discovery

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

I have a ford focus w reg, my passenger door won't open. I can't lock the doors using remote because it only locks three doors, i have to lock the passenger door manually. but now after locking the...


You will probably need assistance with the repair, but first try this. Spray some spray lubricant like WD40 into the keyhole on the exterior using the tiny straw provided with the lubricant can. Try locking and unlocking manually using your key in the outside key lock and try activating the handle to open the door while you have someone pull in and out on the door. Once it's open, you may need to remove the interior panel to see if something is rusted, worn or bent.

Aug 10, 2010 | 2000 Ford Focus

1 Answer

The interior door handle on the driver's side of my 2000 Tundra does not open the door. The exterior door handle works fine. I would assume the cable has broken on the door latch portion. What is the...


remove the screws that fasten the interior door panel to the door.  Visually inspect the handle assembly. there will be two cables that connect the handle and lock button to the door lock assembly.  I would bet that the L-shaped end of the interior door handle cable broke.  The replacement is self explanatory for the handle. Google the door lock assembly which isn't as visable.  Bob

Jan 10, 2010 | 2000 Toyota Tundra

1 Answer

Driver's side door won't open in the cold


.
Power Door Lock Operation (Front Doors)
The front doors do not have traditional door lock actuators. They have electronically controlled door latches that will operate depending on the status of the door lock system. This status is determined by the front door modules and the last known state of the lock system. If the last known state is LOCK, the latches will not release when the door handles are operated. If the last known state is UNLOCK, the latches will release when the door handles are operated. The front doors are also equipped with red door lock status indicators. The front door modules will supply power and ground to the indicators to illuminate them when the lock system is in a virtual state of lock. The indicators will not continuously illuminate when the vehicle is locked. They will illuminate for approximately 5 seconds after a lock switch activation or after a door handle has been operated and the front door modules are in a virtual state of lock. For further information on the front door latches, refer to Power Door Latch Description and Operation .
I would assume they check for DTC'S - diagnostic trouble codes ?
DTC B3062 Front Door Key Lock Switch Circuit
• DTC B3067 Front Door Key Unlock Switch Circuit
DTC B3849 Exterior Door Handle Switch Circuit
The left front exterior door handle and right front exterior door handle switch signal circuits provide inputs to the driver door module (DDM) and passenger door module (PDM) when an exterior door handle switch is activated. These inputs allow the door module to detect a door open request. The door modules provide voltage to the door handle switches. If the door module detects that a ground is applied for greater than 30 seconds continuously, a DTC is set and the door module will ignore the door handle switch input.


Free wiring diagrams here http://www.bbbind.com/free_tsb.html
Enter vehicle info. year , make , model and engine size . Under system click body & accesories .Then under subsystem click power locks . Click the search button then the blue links

Cadillac CTS Door Handle Repair Micro Switches Replacement 2nd Gen

Aug 10, 2017 | 2006 Cadillac STS

2 Answers

Broken exterior door handle,passenger sider ,sliding


Got this idea from mpvclub.com: Get some stainless or aluminum sheet metal screws, drill pilot hole into the handle and into the receiving part behind, then screw in the screw. Do on both sides of handle (get appropriate length screw.) When done, get some putty or hardener to fill in the screw slot, let dry, then sand smooth, then paint with body color. Result is great and inexpensive.

Jan 26, 2009 | 2004 Mazda MPV

1 Answer

1992 Mazda MX-5 Door handle problem.


you will have to take the panel off to see why the inner lock/activator isnt working properly, besides youll have to take it off to fix it anyway.Maybe as simple as a bent handle to lock rod being bent and no longer long enough to activate lock correctly.youll just have to look and see.Let me know what you find

Oct 11, 2008 | 1992 Mazda MX-5

Not finding what you are looking for?
2009 BMW X5 Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...