Question about Honda Civic

1 Answer

Can you please give me the tappet settings for a Honda civic 2004 1.6 Vtec please.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 8,516 Answers

Do you mean 1.7L? I do not see a 1.6L in the manual. Instructions from autozone.com are pasted below.

lash:

Intake, 0.007-0.009 in (0.18-0.22mm).

Exhaust, 0.009-0.011 in. (0.23-0.27mm)

Civic
1.7L Engine

NOTE Adjust valves only when the cylinder head temperature is less than 100 degrees F.

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. Disconnect the negative battery cable.
  2. Note the radio security code and the radio presets.
  3. Remove the ignition coil cover. Remove the ignition coils. Remove the throttle cable clamps and harness holder from the cylinder head cover.
  4. Remove the cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
  5. Remove the grommet from the upper cover and disconnect the camshaft position (CMO) sensor connector. Remove the upper cover.
  6. Set the number one piston at TDC. The UP mark on the camshaft pulley should be at the top, and the TDC marks on the pulley should line up with the top edge of the cylinder head.
  7. Using the proper gauge feeler gauge, adjust the valves on cylinder number one.
  8. Rotate the crankshaft 180 degrees counterclockwise. The UP mark on the camshaft pulley should be toward the exhaust side of the cylinder head.
  9. Using the proper gauge feeler gauge, adjust the valves on cylinder number three.
  10. Rotate the crankshaft 180 degrees counterclockwise and bring the number four piston to TDC.
  11. Using the proper gauge feeler gauge, adjust the valves on cylinder number four.
  12. Rotate the crankshaft 180 degrees counterclockwise. The UP mark on the camshaft pulley should be toward the intake side of the cylinder head.
  13. Using the proper gauge feeler gauge, adjust the valves on cylinder number two.
  14. Install the cylinder head cover.
  15. As required, reprogram the ECM/PCM engine idle characteristics. Be sure all electrical items are OFF.
  16. Start the engine. Hold the idle speed at 3000 RPM-s in park or neutral until the radiator fan comes on or the temperature reached 194 degrees.
  17. Let the engine idle for about five minutes with the throttle fully closed.
  18. If the radiator fan comes on during the five minutes, do not count this toward the five minute programming time.
  19. Set the clock.

Posted on Oct 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tappet gap on 1.6 2003 vtec civic


The firing order is 1-3-4-2. The gap is listed on the emission information sticker under the hood. This sticker will have lots of info which includes valve lash. It will be listed in millimeters, example: 0.22 +/- .02mm. Some feeler gauges list both standard and mm measurements, otherwise a conversion can be found without much trouble. This procedure should be done while the engine is cold to get the best results.

Feb 18, 2015 | 2003 Honda Civic

2 Answers

I have a 2004 Honda Civic VTI, the engine checklight came on and I went to 3 different computer diagnostic centres and the scan showed VTEC system failure. I changed the VTEC solenoid, change vtec pre


What is wrong is that you changed a part

You failed to follow any trouble charts because
you have none

The sensor was most likely okey & just doing it's
job of reporting a fault

You could have a mechanical problem such as a timing
belt issue or worn VVT Actuators on the end of the cames

You have to diagnose code related issues & then find out
why a sensor reported as it did

Even if you scoped the sensor you would most likely
assume it was bad,not so,have to keep thinking why the
data was bad

You need professional tools & look at several pieces of data
overlayed on a big sceen at one time

Repair shop or dealer for that issue

Nov 27, 2012 | 2004 Honda Civic

1 Answer

2002 honda civic p1259 problem


P1259 HONDA - VTEC System Malfunction
Possible causes- Low engine oil pressure or level
- Open or short circuit condition
- Faulty VTEC oil pressure switch
- Faulty VTEC solenoid
When is the code detected?The P1259 is set when there is a problem in the VTEC Oil Pressure Switch circuit or VTEC Solenoid Valve circuit

Oct 01, 2012 | 2002 Honda Civic

1 Answer

What are the intake and exhaust valve tappet clearance specs. of a honda civic 1999 1.6 liter vtec sohc engine?


Valve clearance Inches Millimeters
Intake 0.006-0.007 0.15 - 0.19
Exhaust 0.007-0.008 0.17 - 0.21

Apr 08, 2011 | Honda Civic Cars & Trucks

1 Answer

What is the valve tappet clearance specs. of a honda civic 1999 1.6 liter vtec sohc engine?


Intake: 0.007-0.009 in. (0.18-0.22mm) Exhaust: 0.009-0.011 in. (0.23-0.27mm)

Apr 08, 2011 | Honda Civic Cars & Trucks

2 Answers

Valve tappet clearance of toyota 7k engine and honda civic vtec engine 1.6


7k clearances are ( HOT ) Inlet 0.008 in ( 0.20 mm )
Exhaust 0.012 in ( 0.30mm)

Mar 24, 2010 | 2000 Suzuki Aerio

2 Answers

What engine comes stock in a 1993 honda civic 4 door?


stock engine for that car is a 1.4 in line 4 cylinder with efi.

Mar 03, 2010 | 1993 Honda Civic 4 Door

1 Answer

Honda civic vtec 1995 - 1998 engine wiring diagram


Go to your local library and ask the Librarian to get you on-line to the Automotive Repair Reference Center, and then to the EBSCO database...you will find all of your wiring diagrams there.

Oct 07, 2009 | 1998 Honda Civic

2 Answers

TAPPET SETTINGS HONDA PRELUDE 2.2 IMPORT


Intake valve clearance 0.15mm-0.19mm (6-7 thou); Exhaust clearance 0.17mm-0.21mm (7-8 thou). All measurments COLD engine. 2.2 VTEC Prelude engine 1992-1996, import and UK.

Feb 22, 2009 | 1994 Honda Prelude

1 Answer

Tappet settings


depends on the engine

Jun 30, 2008 | 1995 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

613 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...