Question about 2001 Daewoo Lanos

1 Answer

Thermostat problems Just recently the thermostat housing on my 2001 lanos just blew spitting coolant all over my engine. Does anyone know why this happen, and if so how do i fix something like this?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Try to replace the gasket and see if the corossion did any damage to it, but most of collant leaks are caused by cars than have not been serviced to the cooling system and then the antifreeze gwet old and cause corrotion

Posted on May 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need instructions for replacing thermostat on a 2001 Grand Cherokee 4.7 litre


Do not loosen radiator drain **** with system hot and pressurized. Serious burns from coolant can occur.

NOTE Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse. If thermostat is being replaced, be sure that replacement is specified thermostat for vehicle model and engine type.
Instructions

  1. Locate the Cherokee's thermostat intake housing by following the top radiator hose to the engine. The hose connects to the thermostat intake. A second, smaller hose connects to the left side of the radiator hose. This is a bypass hose for the heater.
  2. Remove the two bolts that secure the Cherokee's thermostat intake housing to the engine with a socket and ratchet and lift the intake upward to drain the coolant in the hose back into the radiator.
  3. Remove the gasket and the thermostat from the engine and discard them. Wipe the mating surfaces of the thermostat intake housing and the engine off with a clean towel.
  4. Place the new thermostat, spring down, into the engine and place the thermostat gasket over the thermostat.
  5. Place the thermostat intake housing onto the thermostat gasket. Thread the bolts into the thermostat intake by hand to avoid cross-threading the bolts and then tighten them using a socket and ratchet.
Additional information:
  1. Clean mating areas of timing chain cover and thermostat housing.
  2. Install thermostat (spring side down) into recessed machined groove on timing chain cover.
  3. Position thermostat housing on timing chain cover.
  4. Install two housing-to-timing chain cover bolts. Tighten bolts to 115 inch lbs. (13 Nm).
    CAUTION Housing must be tightened evenly and thermostat must be centered into recessed groove in timing chain cover. If not, it may result in a cracked housing, damaged timing chain cover threads or coolant leaks.
  5. Install lower radiator hose on thermostat housing.
  6. Install splash shield.
  7. Lower vehicle.
  8. Fill cooling system.
  9. Connect negative battery cable to battery.
  10. Start and warm the engine. Check for leaks.
Good Luck and if this helps don't forget to vote.

Jan 15, 2011 | 2001 Jeep Grand Cherokee

1 Answer

Where is the thermostat and how do I replace it?


  • it is located on the engine (block - in the front).

  • Make sure the engine is completely cool prior to working on the engine. Then place the drain pan underneath the radiator. Open the petcock at the base and let out approximately 1 gallon of coolant.

  • 2

    Unbolt the thermostat housing from the front of the engine using the 3/8-inch ratchet and socket. Coolant will pour out at this point, so be ready for it and aim the hose toward the drain pan if possible. Remove the thermostat and the thermostat gasket.

  • 3

    Clean all of the mating surfaces on the engine and thermostat housing using the gasket scraper. Then install a replacement thermostat in the housing, with the thermostat orienting the same way as the original. Then install the gasket and the thermostat housing on top of it. Bolt it in place using the 3/8-inch ratchet and socket.

  • 4

    Open the radiator cap and fill the radiator with the 50-50 pre-diluted coolant. Turn on the car and let it run for 15 minutes while the interior heat is set on the "high" position. Allow the car to cool for an hour, then add any additional coolant needed



  • Read more: How to Replace a Thermostat in a 2001 KIA Sephia ' eHow.com http://www.ehow.com/how_6111510_replace-thermostat-2001-kia-sephia.html#ixzz16b3EiQc8

    Nov 28, 2010 | 2001 Kia Sephia

    2 Answers

    Where is the thermostat located on 2001 ford focus?


    The purpose of the thermostat is to regulate the coolant system to prevent the engine from overheating. A faulty thermostat will stick and not allow the coolant to enter the engine.
    Follow the upper rad hose to the engine and at the engine there is the thermostat housing.
    Undo the bolts and lift off the connector and replace the thermostat.The thermostat housing is attached with three bolts.Lift the thermostat out of the housing. The thermostat rests at the bottom of the housing.
    -------This will help.Thanks.Helpmech.

    Nov 13, 2010 | 2001 Ford Focus

    1 Answer

    I'm trying to replace the thermostat with a new one but it continues to leak..Is there a ring tht goes with this thermostat? 2001 daewoo lanos s


    You have clean the surface all parts and replace the seals so is the one way that not leaking, If you thermostat housing has two parts ot metal, if not, you have to buy another one with the housing more.

    Jan 12, 2010 | 2001 Daewoo Lanos

    1 Answer

    HOW TO FIX THE THERMOSTAT ON A NISSAN ALTIMA 98


    thermostat should be at the end of the top radiator hose on the engine side.drain radiator most of the way to prevent coolant gushing out when you remove hose.unbolt housing replace thermostat.hope this helps

    Aug 17, 2009 | 2001 Nissan Altima

    2 Answers

    My 2001 jaguar s-type is overheating. does anyone


    Hi,
    The top radiator hose should connect to the thermostat housing, bolted onto your engine. Make sure you get a new gasket.
    Hope this helps... Good luck!

    Jun 10, 2009 | 2001 Jaguar S-Type

    2 Answers

    I need to know where the coolant sensor is on the 2001 Honda Accord EX


    find the thermostat housing and look on the radiator

    Mar 30, 2009 | 2001 Honda Accord

    1 Answer

    How do i replace thermostat in 2001 dodge dakota


    • Drain some coolant into a clean container until the coolant level is below the thermostat housing.
    • Remove the upper radiator hose connection from the thermostat housing.
    • Loosen the housing bolts and remove the housing.
    • Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
    • Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
    • The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
    • When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
    • Install the gasket.
    • Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
    • When the engine has reached operating temperature make sure the thermostat opens.
    • You should be able to see coolant circulating within the radiator.
    • Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
    • If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.

    Nov 21, 2008 | 2001 Dodge Dakota

    3 Answers

    In need of serious help, thermostat problems.


    well The same thing happened to me and I have a Answer!
    It was was just getting to hot and the thermostat housing is Crappy mine blew as well.. so I went to a Toyota dealer and bought the part and put it in my self.... EASY Stuff

    May 27, 2008 | 2001 Daewoo Lanos

    Not finding what you are looking for?
    2001 Daewoo Lanos Logo

    196 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Daewoo Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    yadayada
    yadayada

    Level 3 Expert

    70347 Answers

    Steve Hurc
    Steve Hurc

    Level 3 Expert

    450 Answers

    Are you a Daewoo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...