Question about Ford Fusion

1 Answer

Want to fit fan belt cant find the proper way

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 41 Answers

You have to find the tension pully. using a 3/8 socket wrench. not the socke but the actual wrench. place the square end of the wrench into the notch on the pully and either push or pull (depends on the v-belt system) and it should move. place your v-belt around the pully's according to the diagram under your hood leaving your tension pully to be the last one the belt goes on. Move that tension pully as mentioned above and place it the belt on the pully. The diagram under the hood should also show you where that tension pully is located.

Posted on Oct 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fitting fan belt


2004 Citroen Berlingo 1.4 does not use fan belt - it's electrical fan mounted in front of radiator..

Aug 02, 2012 | 2004 Citroen Berlingo 1.4

1 Answer

I cant get my fan belt on my 1996 300tdi it seems too small.


Find the adjuster idler pulley. It is a pulley that does not drive anything ie aircon, powersteering,waterpump etc. It will have a single 15mm? bolt on it. Fit a suitable spanner on the bolt and turn clockwise. You will find that with minimal force the whole pulley will move and the (old) belt becomes slack. New belt is no longer too small and can be fitted.

Jun 22, 2010 | 1996 Land Rover Discovery

1 Answer

How do u fiT a fan belt on a 55 plate ford focus


Loosen the adjustment bolt on the alternator, remove old belt, fit new one and stretch it slightly with the adjustment of the alternator until you have 2mm of deflection. Tighten up the bolt and take her for a run to charge the battery properly.

Jun 22, 2010 | 2005 Ford Focus

1 Answer

Cant get my serpentine belt back on my 98 deville


Is the belt not fitting properly because of it is too long or too short or is something getting in the way? It must be routed in the proper order. I believe that most cadillacs require the belt to be routed leaving the alternator pulley for last. A long 3/8" drive breaker bar should fit in the center of the tensioner. When you have everything lined up, pry the breaker bar slowly while keeping tension on the belt by pulling the belt onto the alternator pulley. Once it seats, slowly add tension back to the belt stopping every few inches to check the alignment. I hope that is helpful but I have not worked on a caddy in a few years.

Apr 28, 2010 | 1998 Cadillac DeVille

1 Answer

Serpinten belt instalation i need schematics


Possible wrong belt. Idler arm tension may be broken or weak. Make sure you have the belt properly installed.

Jan 30, 2010 | 2004 Dodge Durango

1 Answer

Peugeot fan belt


your fitting it wrong

Dec 22, 2008 | 2006 Peugeot 405

1 Answer

Fitting a new fan belt


Remove the fan shroud cover and draw the fan belts route, loosen the aircon tensioner bolts x 3 on the left side of the cover and remove the aircon belt.With a 15 mm socket on a power wrench pull the auto tensioner to the rightand remove the belt , with a little skill and patience you can get the old belt off and the new one on over the fan blades without removing the fan.Make sure the belt is on properly to prevent it coming off when starting.

Nov 08, 2008 | 1996 Land Rover Discovery

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...