Question about 2001 Pontiac Grand Prix

Open Question

How do i remove the driver's seat in a 2001 pontiac grand prix

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2001 jeep grand cherokee seat removal

i actually removed my 2 front seats very easily as a novice. There really is only i think 4 bolts that need to come out 2 in front and 2 in back. If i can remember correctly i believe it was a larger metric size. Although i dont have power seats, if you do just look for the clip connector and disengage

Posted on Jul 07, 2008

Ad
PyroPCMan
  • 405 Answers

SOURCE: diagram on a pontiac grand prix

Ignition Switch GM Century/Lumina/Grand Prix/Intrigue 1997-2000 The vehicles covered by this guide use one of two types of ignition switches:

  • A mechanical key and lock cylinder built into the steering column, that works a pull rod to actuate the separate electrical portion of the ignition switch mounted further down the steering column. For more information and replacement procedures on this type of switch, please see .
  • An instrument panel-mounted ignition switch is also used on some W-Body vehicles. To service this switch, the radio, heater & A/C control panel and the instrument cluster must be removed. All of these procedures are found elsewhere in this section.
REMOVAL & INSTALLATION
Instrument Panel-Mounted Ignition Switch
WARNING You must perform the Body Control Module (BCM) theft deterrent relearn procedure after replacement of the ignition lock cylinder. Failure to perform this relearn procedure means the BCM will not function properly. This means the vehicle will not be theft protected by the Passlock system and the engine may not crank or start. GM recommends that this procedure be performed with their Tech 2® or equivalent scan tool. An alternate relearn procedure is given at the end of this procedure.
  1. Disconnect the negative battery cable.
  2. Remove the radio assembly following the procedures found in this section.
  3. Remove the heater & A/C control head assembly following the procedures found in this section.
  4. Remove the instrument cluster assembly following the procedures found in this section.
  5. Detach the electrical connectors from the ignition switch.
  6. Insert the key and turn the ignition switch lock cylinder to the ACC position.
  7. Depress the transaxle park/lock cable retainer to release, then pull to remove the cable from the ignition switch.
NOTE You must perform the Body Control Module theft deterrent relearn procedure after replacement of the ignition lock cylinder.
  1. If it is necessary to remove the ignition lock cylinder from the ignition switch (theft damage, etc.), use the following procedure:
    1. Insert the key and turn the ignition switch lock cylinder to the ON position.
    2. Using a small flat-bladed tool, depress and hold the lock cylinder retaining tab.
    3. Using the key as an aid, pull to remove the ignition switch lock cylinder from the switch.
    4. Remove the key from the lock cylinder.
    5. Carefully pull to release the ignition switch bezel from the ignition switch lock cylinder.
  2. Remove the ignition switch bracket bolts and remove the ignition switch through the instrument panel cluster opening.
  3. Remove the bolts retaining the ignition switch to the bracket and remove the bracket.
0900c15280090fea.jpgRemoving an instrument panel-mounted ignition switch assembly—1998 Oldsmobile Intrigue shown, others similar To install:
  1. Install the ignition switch to its bracket and install the bolts. Install the ignition switch into position through the instrument panel cluster opening and install the bracket retaining bolts.
  2. If removed, install the ignition switch lock cylinder to the ignition switch using the following procedure:
    1. Recode the lock cylinder, if necessary.
    2. Align the ignition switch bezel to the tabs on the ignition switch lock cylinder and carefully press to secure in place.
    3. Insert the key and turn the ignition switch lock cylinder to the ON position.
    4. Align the ignition switch lock cylinder to the ignition switch, then press into place.
  3. Turn the key to the ACC position. Align and press into place the transaxle park/lock cable to the ignition switch. Remove the key from the switch.
  4. Attach the electrical connectors to the ignition switch.
  5. Install the instrument cluster using the procedures found in this section.
  6. Install the heater & A/C control panel using the procedures found in this section.
  7. Install the radio assembly using the procedures found in this section.
  8. Connect the negative battery cable.
  9. If the lock cylinder was removed, perform the BCM Programming/RPO Configuration procedure.
THEFT DETERENT RE-LEARN—WITHOUT TECH 1®SCAN TOOL
This procedure takes approximately 30 minutes. Make sure the battery is fully charged before proceeding.
  1. Turn the ignition switch to the OFF position.
  2. Turn the ignition switch all the way from the OFF to the START position, then leave it in the ON position. The engine will not crank.
  3. The SECURITY light should come on and stay on for at lease ten minutes.
  4. Turn the ignition switch to the OFF position for five seconds.
  5. Repeat Steps 2, 3 and 4 again for a second time.
  6. Repeat Steps 2, 3 and 4 again for a third time.
  7. Turn the ignition switch to the OFF position.
  8. Turn the ignition switch all the way to the START position. The engine should now start.

Posted on Sep 09, 2008

ButtFuzz
  • 463 Answers

SOURCE: 2001 Pontiac Grand Prix Gt not shifting into OD

Basic Troubleshooting:

Although the Indicator says the vehicle is in "D" or "OD", is it really? If the linkage is mechanical, you may actually be in "3". Make sure the car is in neutral and pull the lever into the first forward position without looking at the indicator.

Does your vehicle have a switch to turn the OD off and you didn't know it? You may have inadvertently done this. In this case, though, usually there is a little dummy light on the dash that says "O/D off" or something like that.

Check the transmission fluid level on your vehicle and make sure it is to factory specification.

Posted on Mar 05, 2009

  • 5 Answers

SOURCE: srs airbag light is on on my 99 pontiac grand prix

If the seat belt light comes on intermittently with the belt buckled, it may have a bad switch in the buckle or a loose connection @ the switch. This may also set a diagnostic trouble code in the srs control module & keep the srs airbag light on.

Posted on Mar 27, 2009

  • 169 Answers

SOURCE: 2001 pontiac grand prix fuel door is loose and

open the fuel door remove screws for filler remover plastic filler you now have access to fuel door & hinge assemble

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 grand prix not getting enoung voltage to map sensor what could the problem be?


The bolt pattern for a 2001 Grand Prix is 115mm. The Pontiac Grand Prix is an automobile that was produced by the Pontiac division of General Motors. First introduced as part of Pontiac's full-size model offering for the 1962 model year. ----------------------------------------------------------------------------------------------
Car Cables & OBD Connectors

Nov 16, 2012 | 2001 Pontiac Grand Prix

1 Answer

When i turn off the engine its very hard to remove the key its stuck how do i remove the key easily?


Dear Sir:

You must call to some locksmith, for to do the job.

sincerely. God bless you

ernesto cuadra
managua, nicaragua. c.a.

Mar 29, 2012 | 2001 Pontiac Grand Prix

1 Answer

Can I replace my 98 grand prix driver's seat with


You can replace it as long as the one you are replacing is the same set-up. If you have a manual adjusting seat and replace it with a power seat it will fit but you wont have the hook ups for it. Also make sure if it is a bucket seat (single person) you dont replace it with a bench (3 persons fit in front) seat or you will run into problems with the center console and shifter. vice versa may bolt up but there will be a gap between the 2 front seats

Nov 22, 2011 | 1998 Pontiac Grand Prix

1 Answer

I have a 2001 pontiac grand prix the driver window will not go up but goes down fine all the other windows work fine


power window motor is shot. keep window up, if it goes up, because all functions will soon be lost.

Jan 19, 2011 | 2001 Pontiac Grand Prix

1 Answer

2001 Pontiac Grand Prix 2 dr GTP My driver side electric window will go down only if I roll down the passager side at the same time. It is then difficult to roll up, I have to prees hard on the driver...


You will have to remove the button cover with a flat tool such as a screw driver, and use alcohol with a cotton swab to clean the electrical contacts.

Oct 02, 2010 | 2001 Pontiac Grand Prix

1 Answer

I have a 2000 Pontiac Grand Prix se. Both the drivers side windows will not go up/down. I removed the rear door panel of both doors and the small metal cable has come off. Is there a diagram or a fix to...


I had a problem similar to this but mine was in a GT and they would just work when they wanted to. I just had all the wires cut leading to the front passenger seat, back driver seat, and back passenger seat. And left the wires on the main. They all work perfect now. But the downside is that the driver is the only one who can put the windows down. (Which isn't always a bad thing) Hope I could help!

Jul 01, 2010 | 2000 Pontiac Grand Prix

1 Answer

2001 Grand Prix: Is the blower motor resistor on a Pontiac 2001 Gra...


It is behind and underneath the glove box back by the firewall. No need to pull out the glovebox.You may need to pull the carpet back to get to one of the bolts.

May 16, 2010 | 2001 Pontiac Grand Prix

1 Answer

Where are the fuse boxes on a 2001 pontiac grand prix


main box is underhood near relays. Also 1 is on left side of dash behind a panel door, see it when drivers door is open

Jan 08, 2010 | 2001 Pontiac Grand Prix

2 Answers

I need to know where the water pump is in a Pontiac


Try this: http://www.ehow.com/how_5417718_remove-pump-pontiac-grand-prix.html

Dec 05, 2009 | 2001 Pontiac Grand Prix

Not finding what you are looking for?
2001 Pontiac Grand Prix Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...