Question about 1994 Lincoln Town Car

1 Answer

How to get back bolt on starter - 1994 Lincoln Town Car

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 14,036 Answers

TRY USING A SWIVEL SOCKET AND LONG 3/8 EXTENSION SEE WHAT HAPPENS.

Posted on Oct 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removed two bolts from starter and cannot get starter out heard may be extra support bolts but cant locate


I had a Toyota with an odd-ball starter bolt from the back side of where the starter mounted. It didn't even look like a starter bolt, but sure enough, it was. So keep checking, you may have a third bolt you haven't found.

Aug 22, 2013 | 1997 Mitsubishi Diamante

1 Answer

How to remove starter motor from 1997 kia sportage


Most cars only have 2 starter bolts, but some do have 3. An older honda had a third starter bolt from the back side of the transaxle into the starter.
Pull off the electrical connectors, then remove the starter bolts you can see. If the starter is not completely loose now, there must be a third bolt. Check around the starter mounting rim, also on the back side. Good luck.

Dec 02, 2012 | Cars & Trucks

1 Answer

I was changing the starter in my 98 Jetta gt and everything was fine. We got it out but when we tried to put the new one in we noticed that something doesn't line up properly. Somehow the bracket that...


Sounds like the engine mount that connects with the starter bolts shifted a little after removing the starter. Loosen up the engine mount bolts a bit, then, when putting the starter bolts back in, use a pry bar to move the engine mount a little in order to line up the starter bolts properly. Then, once all the starter bolts are are properly threaded in, tighten the starter bolts securely, and re-tighten the engine mount bolts loosened off previously. Hope this helps.

Aug 21, 2011 | 1998 Volkswagen Jetta

1 Answer

Install starter


INSTRUCTIONS: REMOVE NEGATIVE BATTERY CABLE, AIR INLET DUCT,TOP STARTER BOLT,LOWER STARTER BOLT,STARTER ELECTRICAL CONNECTIONS, LOWER STARTER. TO INSTALL:PUT STARTER BACK INTO SPACE, PUT BOTH BOLTS BACK IN SNUG THEM UP THEN TORQUE THEM AT 37 FT.LBS.,REATTACH STATER ELECTRICAL CONNECTIONS( BEST TO MARK WIRES TO WHERE THEY GO AS YOU REMOVE THEM), ATTACH AIR INLET DUCT BACK TO THROTTLE BODY, RECONNECT NEGATIVE BATTERY CABLE.wencal1963_1.gif

Jan 08, 2011 | 2004 Chevrolet Cavalier

1 Answer

How to replace starter


2-4 hrs, depends on experience,
you need metric sockets and wrench set,
hydraulic jack or any jack.
screwdrivers (flats and phillips)
$100+ us dollars for a new starter, with core return.
Disconnect your negative battery cable, on your battery.
Disconnect wirings at your starter:
ignition wires, and power cable.
!!! Important for the electrical wiring !!!
(take pictures, or mark it where goes back, for reference when putting it back together)
Three bolts holds the starter, two medium length bolt
and one extra long bolt
(this the long bolt goes thru your front engine mount).
one of the bolts is double nutted,
first nut secures a cover shroud over your starter,,
second holds the starter.
You need to jack the engine up slightly to relieve pressure off the long bolt when removing, also to prevent engine from dropping when long bolt is removed. when all bolts are removed starter should come out easily.
install new starter in reverse order, take pictures, mark all hardware make sure they go back in the same place,
mark or take pictures of your wiring before disconnecting.

Good Luck!
RMak

Sep 01, 2010 | 1996 Volkswagen Jetta

1 Answer

How do i connect my starter to the battery


REMOVAL & INSTALLATION 2.2L (VIN 4) Engine Fig. 1: Removal and installation of the starter — 2.2L engine shown 87952039.gif
Fig. 2: Remove the starter electrical connections from the back of the starter 91142p05.jpg
Fig. 3: Remove the three bell-housing cover retaining bolts and . . . 91142p06.jpg
Fig. 4: . . . remove the bell-housing cover 91142p07.jpg
Fig. 5: Remove the starter support brace-to-engine bolt 91142p08.jpg
Fig. 6: The starter is retained by two bolts 91142p09.jpg
Fig. 7: Remove the bolts and . . . 91142p10.jpg
Fig. 8: . . . remove the starter from the engine 91142p11.jpg
Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside 91142p12.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter. To install:
  8. Transfer the starter support bracket to the new starter if the starter is being replaced.
  9. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  10. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  11. Install the bell-housing cover.
  12. Install the starter electrical connections on the back of the starter. Tighten the "S'' terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  13. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines 87952040.gif
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle. To install:
  9. Raise the starter to the vehicle, then attach the wiring.
  10. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  11. If moved, reposition the engine wiring harness.
  12. Carefully lower the vehicle.
  13. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  14. Fasten the air inlet duct to the throttle body.
  15. Connect the negative battery cable.
prev.gif next.gif

Aug 19, 2010 | 1996 Chevrolet Cavalier

2 Answers

Where is the starter on a 1998 cavalier z24


1998 Chevrolet Cavalier 2.4L SFI DOHC 4cyl - Repair Guide
Look at the the lower end of the engine behind the radiator.

REMOVAL & INSTALLATION

2.2L (VIN 4) Engine

b30d4a5.jpg

Fig. 1: Removal and installation of the starter-2.2L engine shown

ce77b94.jpg

Fig. 2: Remove the starter electrical connections from the back of the starter

a7d8ae8.jpg

Fig. 3: Remove the three bell-housing cover retaining bolts and ...

3580a66.jpg

Fig. 4: ... remove the bell-housing cover

95f5421.jpg

Fig. 5: Remove the starter support brace-to-engine bolt

225716e.jpg

Fig. 6: The starter is retained by two bolts

51b21e5.jpg

Fig. 7: Remove the bolts and ...

35a623c.jpg

Fig. 8: ... remove the starter from the engine

3658d11.jpg

Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter.
To install:
  1. Transfer the starter support bracket to the new starter if the starter is being replaced.
  2. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  3. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  4. Install the bell-housing cover.
  5. Install the starter electrical connections on the back of the starter. Tighten the S terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  6. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines

7ac0166.jpg

Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable accese to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle.
To install:
  1. Raise the starter to the vehicle, then attach the wiring.
  2. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  3. If moved, reposition the engine wiring harness.
  4. Carefully lower the vehicle.
  5. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  6. Fasten the air inlet duct to the throttle body.
  7. Connect the negative battery cable.

I hope help you with this (remember rated this help) Good luck.

Oct 12, 2009 | 1998 Chevrolet Cavalier

1 Answer

Reinstall of Starter 1998 2.4L Chev Cavalier


moz-screenshot-4.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter.

To install:
  1. Transfer the starter support bracket to the new starter if the starter is being replaced.
  2. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  3. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  4. Install the bell-housing cover.
  5. Install the starter electrical connections on the back of the starter. Tighten the S terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  6. Carefully lower the vehicle, then connect the negative battery cable.

2.3L (VIN D) and 2.4L (VIN T) Engines
See Figure 10


0900c1528003cb99.jpg

Apr 08, 2009 | 1998 Chevrolet Cavalier

3 Answers

Replacing started/ how many bolts hold in on?


starter has two bolts. make sure you are using self locking washers. you could also use thread tape or buy a tube of locktite. bolts are about 4-5 inches

Mar 31, 2009 | 1992 Pontiac Grand Am

Not finding what you are looking for?
1994 Lincoln Town Car Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...