Question about 2002 Lexus LX 470
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Perform steps 1-3 first to inspect whether you have the access doors or not before ordering filters!!!
Did this little project this evening. Figured I'd write it up.
5 Easy steps:
1. Remove glove box door by removing both screws at the bottom of the door.
2. First pop the the little flap with a fuse/relay out of the black plastic shield in the upper portion of the glove box opening. Next push it back behind the shield through the opening. Next remove the 3 screws holding the shield in place. Don't pull this shield out yet!! Read step 3 first.
3. Gently pull the shield out. Be careful because the glove box light is still plugged into this part. It is located on the right side of the shield. Once it is pulled out slightly, unplug the bulb from the harness and now you can fully remove the part.
4. Now you can see the vertical cover where the air filters reside. The cover is about 5 inches tall and about 1 inch wide. It has 2 tabs on the upper portion of the cover. Squeeze these tabs towards each other and pull the cover off.
5. The filters are now exposed. They are stacked on top of each other. Pull the first filter out then lift the next filter up and pull out. Put new filters back in and reverse the procedure.
2 Cabin air filters (Toyota PN 88568-60010 if you drop CDan a pm)
1 Phillips screw driver
No more than 15 minutes
STEP BY STEP PHOTO INSTRUCTIONS
Thanks for using FixYa - a FixYa rating is appreciated for taking the time to answer your FERE question.
Posted on Mar 19, 2009
The port should be located on the top left of the engine. Look for compressor and follow tubes toi the back of compartment nearest to firewall. The port should be plainly labeled.
Posted on Jun 23, 2009
Pull the wheels off the back of the car. remove the rubber plug on the rotor hub and rotate the rotor to where the hole is on the bottom and look in there. you should be able to see a sprocket. take a long flathead screwdriver and move it up or down until the rotor does not freely move. then turn it two times in the opposite direction. do this for both sides then you should be good to go! good luck!
Posted on Nov 14, 2009
Is the suspension fluid low. If it is, try first to add specific Suspension Fluid for LX470. It is part number 08886-01805 and any Lexus Dealer would be able to look up. Cost about $ 30 it comes in 2.5 Liters. If driving at higher speeds it is normal for it to drop just a bit and resume to balanced height when parked.
Posted on Jul 21, 2010
The hydraulic system that operates your brakes will not work if any air has gotten into it. Check your resevoir , if it is still full , then I would guess that the brake Master Cylinder is worn out.
The system can be refilled , and the air bled out of all the lines , however , if there is a leak in the system or the master cylinder is bad your problem will not be solved.
Posted on Jan 31, 2011
Tips for a great answer:
Sep 30, 2013 | 2001 Lexus LX 470
Nov 18, 2010 | 2002 Lexus LX 470
Feb 27, 2010 | 2003 Lexus LX 470
Jan 25, 2010 | 2004 Lexus Lx 470
Dec 27, 2009 | 2005 Lexus Lx 470
May 09, 2009 | 2007 Lexus LX 470
Aug 11, 2008 | 2002 Lexus LX 470
Jul 03, 2008 | 2002 Lexus LX 470
72 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: