Question about 2002 Kia Sportage

Open Question

Leaky water pump just need diagram on how to remove it.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace a water pump on my plymouth grande voyager se 3.3l


Jack up the passenger side and remove the tire. Remove the splash shield to gain access to the belt and tensioner. Remove the serp belt. Remove the bolts holding the pulley to the water pump. Remove the pulley Remove the bolts holding the water pump to the timing cover. Remove the water pump. Be prepared for the bolts to break. It happens often!

Jul 13, 2013 | Cars & Trucks

1 Answer

Need a diagram showing exactly where the water pump is located on a 97 cadillac deville northstar


zjlimited_1587.jpg

Fig. Water pump assembly-4.6L Northstar engine (click image for zoom)



zjlimited_1588.jpg



Fig. Remove the water pump belt shield


zjlimited_1589.jpg


Fig. Remove the water pump adjuster pulley retaining bolt and


zjlimited_1590.jpg


Fig. Remove the water pump retaining bolts




Hope helps.


Jul 16, 2011 | 1997 Cadillac DeVille

1 Answer

Leaky water pump % cross over gaskets


there are weep holes in the back of water pump if water is cming out of those weep holes you need to replace water pump if its just the water pump gaket R & r gasket make sure hose clamps are tight & hoses are not leaking before coneming water pump

May 31, 2011 | 2006 Chevrolet Impala

1 Answer

Having problems taking the water pump off my 1993 dodge Shadow Os there a diagram of where the bolts are all located?


FOR THE 2.2L AND 2.5L ENGINES TO REMOVE WATER PUMP THE AIR CONDITIONER COMPRESSOR AND BRACKET NEED REMOVING AND ALTERNATOR AND BRACKET HAS TO BE REMOVED BEFORE WATER PUMP CAN BE REMOVED.

Jan 20, 2011 | 1993 Dodge Shadow

1 Answer

How do i remove the water pump pulley or impeller so I can replace the leaky seal and re-install the pump? Do i need a puller ? If so, do I pull off the impeller or the pulley?


You don`t remove the impeller.The new one comes with it.Just remove the water pump and install the new one.Hope this helps.Good luck.

Nov 12, 2010 | 2004 Dodge Grand Caravan

1 Answer

WATER PUMP REPLACE DIAGRAM


  1. Step 1 Drain the antifreeze from cooling system. Remove belt from water pump. Examine and see if you have to remove anything else to get out the water pump. If so make a diagram of everything you are removing so you can put it back together.
  2. Step 2 Remove the hoses from the water pump. Find all bolts holding the water pump in . Loosen each one a little bit. After all are lose you can then remove them. Remove water pump. Put new gasket on and install new water pump. Hook up hoses to water pump. Look at your diagram and replace everything you had to remove earlier. Put the belt back on.
  3. Step 3 Shut the drain on system and refill cooling system. Make sure you use the antifreeze that is designed for system. Run engine for a couple of minutes. Check for leaks and check coolant level. Add if necessary. If there is no leaks you are ready to go.

Jun 04, 2010 | 2001 Mazda MPV

2 Answers

1992 volvo 240 timing belt replacement


timimg belts usually don't make noise, they break and the motor stops!! The noise could be coming from a bad water pump, powersteering pump, air compresser, alternater, leaky exhaust, leaky vacume lines. Check them out. Or, I don't know the condition of the engin. Has it been neglected and are the bearing going? More history would be helpful.

Jun 15, 2009 | 1992 Volvo 240

1 Answer

Having trouble getting water pump out of 94 lantra 1.8 lt


1. Remove the alternator & power steering pump drive belts.
2. Remove four (4) 10mm bolts holding the water pump pullys & remove the pullys.
3. Drain the Radiator (save coolant if intend to reuse).
4. Loosen & remove AC compressor belt.
5. Remove crankshaft pully (22mm bolt).
6. Remove lower timing belt cover (10 mm bolts) to access water pump bolts.
7. Remove the water pump (12mm bolts)
(1) Remove the 2 bolts, then remove the alternator brace (A). (2) Remove the water pump (B) and gasket.
dbb00ee.jpg ef0cc15.jpg 8. Clean mating surface on engine & install new gasket & pump - reassemble. Refill w/50-50 coolant.

Mar 21, 2009 | 2004 Hyundai Elantra

Not finding what you are looking for?
2002 Kia Sportage Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...