Question about 1996 Ford Ranger SuperCab

1 Answer

1996 ford ranger clutch bleeding how t o - 1996 Ford Ranger SuperCab

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 343 Answers

Bleed just like you do brakes; from clutch slave cylinder located on passenger side of bell housing... reply if you have never bled a hydraulic system...

Posted on Oct 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Grinding noise


clutch is not disengaging enough . check the fuid in the clutch resivoir fill and bleed the sys

Feb 28, 2014 | 1996 Ford Ranger SuperCab

1 Answer

How to bleed 89 ford ranger 4x4 clutch


there is a bleeder screw by the transmission slave cylinder that you bleed the air out.just pump the clutch pedal a few times hold the pedal to the floor and have someone crack open the bleeder screw to bleed the air out then close it and repeat.make sure the master cylinder for the clutch doesn`t go low.

Nov 02, 2011 | 1989 Ford Ranger

1 Answer

How do you bleed a hydrolic clutch for a 1999 ford ranger?


you need 2 people one in cab and one down at clutch cylinder have one pump clutch and hold down ,and other person open bleed to let air out keep repeating this operation until you have no air coming out just fluid dont forget to keep topping up reservoir

Mar 28, 2010 | 1999 Ford Ranger SuperCab

3 Answers

How to bleed a clutch in a ford ranger


http://www.therangerstation.com/tech_library/bleedclutch.htm

Dec 07, 2009 | 1995 Ford Ranger Supercab

4 Answers

No clutch pedal been bleeding it for 3 days. i have replaced the slave cylinder, clutch and clutch master cylinder. its a 1994 ford ranger 2.3L 5speed


On a Ford Ranger you need to have the clutch master cylinder facing up when you are looking at it mounted on the vechile it is pointing down you need to have it facing up and also have a bleeding tool I went out and bought a POhoenix Injector which makes it real easy and you can do it buy your self. Good luck

Dec 06, 2009 | 1994 Ford Ranger Supercab

1 Answer

Ford f 350 clutch bleeding with no bleeder


there is a bleeder. see picture, bleeder is small tube.
87485f9.jpg

Mar 13, 2009 | 1996 Ford Ranger SuperCab

1 Answer

Bleed cluch 96 ford ranger


Ok you want to check if your slave cylinder is bled and that is the pressure plate. However, the clutch may have pressure, it dose not always engage the clutch all the way witch would cause a slamming of the clutch. Anothing thing is to check is that if you have had your clutch changed recently make sure that the proper clutch has been in staled because there are a couple diffrent choises out their. If thats not it all I can think of is your slave cylinder fluid is low. You can use a hand held brake vaccum bleeder to do this as well and it removes a bunch of the air.

Bleeding a clutch properly removes all the air from the clutch line. You want to remove the air through the master cylinder at the top of the clutch system rather than through the bottom by pumping the clutch pedal. Pumping the clutch will not remove all the air. Bleeding the clutch on a Ford Ranger will take about 20 or 30 minutes.

Raise your truck 6 inches off the ground with a jack. You can drive the truck on ramps if you have them. Lifting the truck will make it easier to bleed the clutch I promise.

Use a turkey baster to **** the brake fluid out of the brake fluid reservoir located at the top of the master cylinder.

Fill the pump style oil can with brake fluid and attach the flex line to the opening on the oil can. Use a new can. You do not want to pump dirt particles or another fluid into the clutch line. This is just good practice I think.

Pump the flex line with brake fluid to remove all the air. You do not want to add additional air to the clutch system.

Open the bleeder valve located on the internal cylinder with a 7mm wrench and quickly attach the flex line to the valve. I believe this is the wrench you need this is what the size of my ranger is but yours may differ. (Remember the slave cylinder may be inside the transmission bell housing.)

Pump the can to move brake fluid up the clutch line. Stop when you no longer see bubbles coming out of the brake fluid reservoir. It should take about 5 minutes to remove all the air from your system.

Use the wrench to close the bleeder valve and remove the flex line from the bleeder valve and this should complete your job.

I hope you have the best of luck with this project!

Feb 26, 2009 | 1996 Ford Ranger SuperCab

1 Answer

1996 Ford Ranger XLT Clutch Bleeding


The problem is up at the Master Cyl............It comes ou of the firewall and points DOWN at about a 45 deg angle.....The reservoir is remote and the hose is set to the lowest point of the cyl...........The tube TO the slave is 180 deg around facing bottom...........
Take the master cly OFF the firewall.......tilt it so that both inlet and outlet are the HIGHEST point of the cyl........Gravity bleed or vacula the slave.........then reinstall the master
I know it sounds like a lot of work but it's the easiest way to clear the air out of Ranger/Explorer hydraulics

Aug 11, 2008 | 1996 Ford Ranger SuperCab

1 Answer

Need step by step on how to bleed hydrolic clutch on a 1996 ford ranger


First remove the clutch reservoir top. Make sure the rubber stopper/bladder is in the cap when removed. Next locate the clutch line that goes into the tranny just aft of the bell housing. There should be a bleed screw, if so open it slightly. If no screw, than loosen the line where it attatches in. Next fill the clutch reservoir and watch till it leaks out on the tranny end. Once thats noticed, close the screw/line and recap reservoir. pump clutch pedal, and repeat bleed steps at least once more to ensure all air is out. remember to fill clutch fluid up to operating levels.

Jul 20, 2008 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
1996 Ford Ranger SuperCab Logo

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...