Question about 2006 GMC Envoy Xl

2 Answers

STORED DATA IS IT POSSIBLE TO RETRIEVE THE MAXIMUM SPEED THAT MY ENVOY HAS BEEN DRIVEN FROM THE CAR'S COMPUTER? IF SO, HOW? THE LOCAL DEALERS DON'T KNOW. I AM HOPING TO GET THIS INFORMATION TO CONTEST A SPEEDING TICKET. THE TICKET WAS WRITTEN FOR 87 MPH AND WE HAVE NEVER HAD THE VEHICLE OVER 80 MPH. ANY INFO WOULD BE APPRECIATED. THANKS, CHAD MILLER CMILLER@JFALLENCO.COM

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 310 Answers

If u have car, then try it

Posted on May 27, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 1,894 Answers

Does ur car has a computer system with it.?
if so u can try to retrive

Posted on May 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

05 envoy wont shift to 3rd gear speedo quit working abs light and brake light on too help


have code retrieve it is normal for transmission won't shift if there is no speed to pcm
ABS light on there is no speed for him too and brake light
look for wire at transmission for speed sensor or why no speed sensor not working

Oct 15, 2013 | 2005 GMC Envoy

1 Answer

Dodge ram won't start and ECM light and check


First you need to retrieve the trouble codes stored in the computer.If you don't have a code reader or scan tool you can take it to your local autoparts store (advance auto,autozone,ect) and they can retrieve them for you.Then we can go from there.

Jan 12, 2012 | 2007 Dodge Ram Truck

3 Answers

AFTER ABOUT 15 MINUTES OF DRIVING 3RD GEAR GOES OUT AND I ONLY HAVE 1ST & 2ND GEAR UNLESS I STOP WHERE IM AT TURN IGNITION OFF WAIT A FEW SECONDS THEN CRANK IT BACK UP AND IT GOES FINE.


I agree completely with Michael Masters with one acception: Some faults, like erratic speed sensor input to the Body Control Module can cause "Limp-In Mode". Also, there are some ABS and/or Traction Control codes that can cause this. these types of codes CANNOT be retrieved for FREE using the generic OBD code readers at the auto parts places. These will require a full computer NETWORK scan using a scan tool that can access body controls, IPC data, ABS data, etc. The "free" way is worth a shot, but if they tell you there are no codes, then you need to take it to a professional technician that can provide a FULL scan.

Oct 25, 2011 | 2000 Chrysler Town & Country

2 Answers

My 2002 Envoy engine shuts down in low, i notice a huge leak of dex cool in drive way, also when i turn of the air condition the rpm goes down and sound like ready to shut down. The rear its un level righ...


I don't see any need to go into a long story here

You have at least two problems that may not be
all that big a deal

I would flat bed it to a dealer or local repair shop

Sep 23, 2011 | 2002 GMC Envoy

1 Answer

Service engine light is on


3 Options !

1st : Go to your local GM Dealer, they will read the Code to know what's the defective or broken part on your vehicle !

2nd : Go to a Local Garage who do maintenance on vehicle they will do the same as the dealer !

3rd : Go to a local store that sell's automotive product and part's you could buy your own Obd2 Scanner, would cost depending between 70-150 $ but you don't need to buy the most expensive one ! To read the Check Engine Code, will tell the P0... code !

Aug 11, 2010 | 2004 GMC Envoy

2 Answers

SUV unintentionally accelerating


YOUR VEHICLE IS NOT SAFE TO OPERATE:

Contact your local GMC Dealer.

We have pulled the recall data for your vehicle and no one has reported this problem.



Hope this tip helps.

r/
David

Feb 26, 2010 | 2003 GMC Envoy

1 Answer

Electrical Problem with speed gauge, RPM and dash board lignts.


That is a manufacturing defect associated with your instrument cluster. My local dealer replaced my entire instrument cluster for free (truck was out of warranty) when my speedometer showed 100 mph in a parking lot and my oil pressure gauge read 0.

Jan 01, 2010 | 2004 GMC Envoy

1 Answer

3 codes present on my 2002 Envoy. p0172, p0420, and p0340,


Track the p0340 first camshaft timing is very important and could possibly cayse your other codes,Call your local GMC dealer I think I remember a bulletin about this code.

Aug 21, 2009 | 2004 GMC Envoy

1 Answer

I was driving and the rpm's decreased and the speed wouldn't go over 20. later in the day the engine light came on. I took it for an oil change a few days before but doubt that has anything to do w/ it....


most likely torque converter problem if fluid is decreasing, but could be other problems my advice take it to a good transmission shop or the dealer, also you can if you want retrieve the code in the computer by following the instructions in the repair manual ex:haynes or chiltons for retrieving the codes from the ecu or you can buy an OBDI dianostic scanner from local parts store

Jan 20, 2009 | 1994 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...