Question about 1988 Dodge D-Series Pickups

Open Question

Need to know ignition timing procedure for a 1988 Dodge 318

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1988 Dodge Ram 150 318 V-8

check the starter relay or the ignition moduale which is located behind the distributer

Posted on May 10, 2009

Ad
  • 6982 Answers

SOURCE: what is ignition timing for a 1972 dodge dart 318

factory is TDC but most like to run at 4 degrees advanced.

Posted on Sep 13, 2009

marshalljc
  • 51 Answers

SOURCE: I have a 1985 dodge ram with a 1988 318 engine no

have the module tested. check for voltage at the dis and coil

Posted on Oct 24, 2009

elshaddai159
  • 1016 Answers

SOURCE: 1988 dodge 318 i need to reset my spark plug

Hi,

Heres the firing order you were after.

29c767e.jpg
Hope this helps, let me know and please rate this solution.

Thanks

Jason

Posted on Aug 17, 2010

  • 17 Answers

SOURCE: We have a 1988 Dodge

on the passenger side under the alternator its bolted to the block

Posted on Dec 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1988 Dodge Ram 4x4. Its a v8 318 throttle body. When I got it, the distributer cap & 12 volt coil was missing. I need to know how to put them on


Distributor cap will have an alignment notch and will only fit on one way and the ignition wire will go to the positive side of the coil and the negative side to the distribuotr points.

Oct 12, 2014 | Cars & Trucks

1 Answer

318 starts but wont stay running blows black smoke out tailpipe. It has new fuel pump, filter,timing chain plugs,wires...


The older chrysler products have a ballast resister on the firewall that is used for dropping the voltage to the ignition coil. During a start procedure, while the key is turned all the way in start position 12 volts bypass the resistor forcing a high output of coil voltage. When you release the key to the run position 12 volts goes ito the resistor & a lower voltage of around 6-7 volts comes out, & goes to the coil.
What happens, is the resistor breaks inside and no voltage is coming out the resistor. Thus only a start condition exist with no run.

Sep 15, 2010 | 1988 Dodge Ramcharger

1 Answer

Need the procedure for setting ignition timing on a dodge truck with a 318 motor year is 2001


hook up to timing light, start vehicle. loosen distributor hold down bolt. aim timing light at timing mark. rotate distributor either way untill the proper mark lines up, then tighten hold down clamp, shut off vehicle then unhook timing light. rpms should be at least 650 to 700, for automatic tranny.

Aug 19, 2010 | Dodge Pickup Cars & Trucks

1 Answer

1988 dodge 318 i need to reset my spark plug wiring i cross them up can you help that it


Hi,

Heres the firing order you were after.

29c767e.jpg
Hope this helps, let me know and please rate this solution.

Thanks

Jason

Aug 17, 2010 | 1993 Dodge Ram 250

2 Answers

1989 Dodge Truck B250 Van V8-318 ignition control module location?


its built into the ecm located right in the middle of he firewall from under the hood, big black box with two plugs.

Jan 31, 2010 | 1988 Dodge B250

1 Answer

Missing hose from map sensor


to any place where it has constantly got vaccuum from the intake manifold.

May 06, 2009 | 1988 Dodge D-Series Pickups

1 Answer

Ignition problem


It should be underhood, driver side on upper firewall, it does not look like a typical ignition module, but I looked around and for your info, you can find a picture of it on autzone.com Hope this helps.

Sep 26, 2008 | 1988 Dodge B250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...