Question about 1991 Plymouth Acclaim

1 Answer

Which spark plugs are used for the 2.5 litre 4 cylinder engin on a 1991 Plymouth acclaim

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 84 Answers

NGK Vpower Stock Number 2635 or
NCK GP Platinum Stock Number 2763 will work with this vehicle. Remember you need 4 of either.

Posted on Oct 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1991 Plymouth Acclaim 4 cylinder runs great for about 15 miles, then acts like it's getting no power


Use a bottle of yellow HEET dry gas to remove any moisture problem in the fuel.

Clean / replace air filter.

Top off ATF to MAX level.

Mar 29, 2013 | 1991 Plymouth Acclaim

2 Answers

I have a 1991 Plymouth Acclaim - 4 cylinder. It will start and run for a while but if I make about 2 runs and come back out to start it, it just turns but will not catch. If I let it sit for about 4-5...


It sounds like your ignition coil is over heating. Was the coil replaced? Your mechanic should have checked voltage/resistance and replaced if needed since it is not too expensive and is a major part of tune-up and ignition system. You can change yourself in a few minutes and save some cash. I had the same problem and had to wait for coil to cool before it would start again. Hope this helps.

Jul 11, 2011 | 1991 Plymouth Acclaim

1 Answer

I did a tune up but now 94 plymouth acclaim will turn over but will not start


Check to ensure that all ignition wires are properly seated...especially the coil wire at the distributor. make sure there are no disconnected ground wires at the source of your sparkplug wires. and... check to see if the spark plugs may have a different top that may not be compatible with the plug wire ends.
Use an insulated screwdriver hold handle and plug it into a plug wire. Rest the screwdriver shaft a quarter inch from some bright metal on the engine and have someone crank the engine. You should have a spark off the gap between driver and grounded part. If not, begin looking at ground wire from battery and engine to frame ground link usually a braided metal cable.

Mar 11, 2010 | 1991 Plymouth Acclaim

1 Answer

Took plugs off the 1994 plymouth acclaim distributor cap now dont know which plugs go where


the cap should have the cylinder numbers stamped next to the wire connections showing which wire goes where. the cylinders are as follows on a 3.0l:

firewall

1 3 5

2 4 6

bumper.

on the 4 cylinder models i imagine it is:

1 2 3 4
lol

Jun 23, 2009 | Plymouth Acclaim Cars & Trucks

1 Answer

Change wather pump 1991 plymouth acclaim


Try (autozone.com ) & sign up for free access to manuals, pictures, step by step instructions plus parts prices. Just enter your vehicle info & go to manuals, click on engine & engine overhaul, then scroll down left side & click on water pump.

Jun 05, 2009 | 1991 Plymouth Acclaim

2 Answers

Car wont crank 1994 plymouth acclaim


Not sure what yor experiencing . Do you have crank no start or no crank no start? No crank no start is battery and cables issue. Crank no start is ignition , plugs, and fuel.

May 28, 2009 | 1991 Plymouth Acclaim

1 Answer

Plymouth acclaim wont start,no spark,no fuel


Do me a favor and cycle the key to on, then off, then on, then off, then back to on,& leave it in the on position.(not start) Now watch & record any flashes of the check engine light. You will get a number of flashes, then a pause, then more flashes. for example: 3 flashes, pause, then 3 more, would be code 33. It will always be a 2 digit number. 2 flashes,pause then 5 flashes, is code 25. When you get 5 flashes, pause then 5 more, that's code 55 which means end of message. Get back to us with any codes that flash.

May 25, 2009 | 1991 Plymouth Acclaim

Not finding what you are looking for?
1991 Plymouth Acclaim Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...