Question about 2001 Toyota Tacoma

Open Question

Torque specs on flywheel and clutch assembly - 2001 Toyota Tacoma

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

  • 1 Answer

SOURCE: torque specs for the flyhwheel of a 1998 toyota tacoma?

Thank you for responding. They figured out by talking to another mechanic what they needed to do. They just didn't know how much torque was needed and since the mechanic didn't know either he told them how to tighten it. It appeared to work. Again I appreciate you getting back to us.

Posted on Dec 31, 2008

chuck943
  • 783 Answers

SOURCE: torque specs foe 4.9 ford f150 flywheel

75-85 ft lbs

Posted on Mar 04, 2009

  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 gmc canyon 2.8l manual transmission flywheel torque specs. And pressure plate torque specs.


Flywheel - 18 ft lb plus an additional 50 degrees
Clutch plate - 15 ft lb

Dec 05, 2016 | 2006 GMC Canyon

2 Answers

Flywheel replacing


you will need a replica flywheel and new bolts plus torque range and manfacturers specs.

Nov 07, 2016 | Cars & Trucks

1 Answer

? looking the bolt tension specs for flywheel and clutch pressure plate for 4hf1 thank you


Torque Specification - National Truck Spares ' Parts

www.nationaltruckspares.com.au/Parts.aspx?ProductTypeID=8...
1073, 4BC2 tq, Isuzu, Torque Specification, KT26 TLD57 NKR57 NPR57 ... 1075, 4HF1Tq, Isuzu, Torque Specification, NKR66 NPR66, 92 - 03, 4HF1, 4334

Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

boxwrench.net/specs/chevy_sb.htm
Flywheel (Clutch). Thread Locker, 60 ft-lbs. Clutch Pressure Plate, Thread Locker, 35 ft-lbs. Centerbolt. (Harmonic Damper). Engine Oil, 60 ft-lbs. Bellhousin

Nov 07, 2015 | Cars & Trucks

1 Answer

What are the torque specs for the flywheel bolts?


Flywheel bolts are usually torqued up to 60ft lbs.
Use some threadlock, too

Nov 02, 2015 | Ford Cars & Trucks

1 Answer

Installing piloet bearring in flywheel


Hi Snale, The bearing is located inthe center of the fly wheel. To gain acsess means removing the gearbox, clutch assembly and flywheel. Gain access from the back of the flywheel. Tap out the failed bearing, fit in the replacement and refit the flywheel. Make sure to torque the fly wheel bolts to the required specs. This is a major undertaking and even though the bearing is very small the job is very big. Regards John

Nov 16, 2012 | Cars & Trucks

1 Answer

03 tiburon clutch torque specs


your torque specs for clutch to flywheel
15-22NM

Jul 11, 2009 | Hyundai Motor 1997 Tiburon

1 Answer

I need torque specs for 94 rodeo


flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Feb 14, 2009 | 1995 Isuzu Rodeo

1 Answer

2003 Tiburon 6 spd clutch replacement now tranny won't respond


Possibility, you may have intalled the clutch disk backwards.... if so, the disk hub is torqued against the crankshaft hub preventing engagement of the clutch. 2003 TIBUORN DUAL MASS FLYWHEEL AND CLUTCH DISC ASSEMBLY INSTALLATION PROCEDURE DESCRIPTION: The 2003 MY 2.7L Tiburon vehicle equipped with the 6-speed manual transaxle employs a dual mass flywheel system. The 2003 Tiburon Shop Manual does not show the clutch disc assembly with the dual mass flywheel. This bulletin provides information about how to assemble these components. NOTE Although it is possible to assemble the clutch disc with either side facing the flywheel surface, only the assembly of these two parts shown in this bulletin is correct.
PARTS ASSEMBLY:
  1. Attach the dual mass flywheel to the engine crankshaft assembly.
  2. Identify the clutch disc flange side and the collar side as shown. 0240025a.gif
  3. Install the collar side of the clutch disc on the dual mass flywheel surface so that the flange side is facing the pressure plate side as shown. 0240025b.gif
  4. Attach the pressure plate to the dual mass flywheel and complete assembly of the remaining components per the Shop Manual procedures. 0240025c.gif

Dec 14, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2001 Toyota Tacoma Logo

Related Topics:

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...