Question about 1997 Mercury Grand Marquis

Open Question

Need diagram of rear brake lines for 97 grand marquis?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
warlock61
  • 659 Answers

SOURCE: i need a diagram of 2000 grand marquis serpentine belt

here you go

7d04ab2.gif

Posted on Dec 28, 2008

Ad
  • 4369 Answers

SOURCE: replace rear brake pads on a 2000 grand marquis

rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Posted on Mar 15, 2009

greg_margo
  • 1959 Answers

SOURCE: Rear Drum Brake Install

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the drum retaining nuts, if equipped, and remove the brake drum.
If the drum will not come off, pry the rubber plug from the backing plate. Insert a narrow rod through the hole in the backing plate and disengage the adjusting lever from the adjusting screw. While holding the adjustment lever away from the screw, back off the adjusting screw with a brake adjusting tool. Be careful not damage the notches in the adjusting screw or the self-adjusting mechanism will not function properly.
  1. Inspect the brake drum for scoring and wear. Replace or machine as necessary. If machining, observe the maximum diameter specification.
To install:
  1. If a new drum is being installed, remove the protective coating from the drum using brake cleaner. Sand the drum lightly and wipe with a cloth soaked in denatured alcohol.
  2. Adjust the brake shoes according to the procedure in this Section.
  3. Install the brake drum and the wheel and tire assembly.
  4. Lower the vehicle.
http://www.chiltonlibrary.com/content/images/8665/images/86659045.pdf

http://www.chiltonlibrary.com/content/images/8665/images/86659046.pdf

The 2 links are diagrams for shoe placement and the automatic brake adjuster.
Be sure to have the drums turned before installing the brake shoes.

Hope this answers your question. Best of luck on your repair.
Greg

Posted on May 28, 2009

MNfisherman
  • 11896 Answers

SOURCE: REAR BRAKE SHOE ASSEMBLY DIAGRAM

You can go to autozone.com and register for full free online repair manual that has the diagrams you need and everything else you could want.

Posted on Nov 18, 2009

  • 239 Answers

SOURCE: need a full brake line diagram for 1992 ford

Too many variables here. Is there fluid in the master cylinder in the rear brake portion? Does a brake warning light come on when the brakes are applied? Is the pedal solid when braking or does it feel spongy? You could have a problem with the metering or proportioning valve. Since brakes are a safety item I suggest you check with one of the shops that offers free brake inspections.

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake line diagram for 96 grand marquis. Leaking driver side rear wheel


Probably the wheel cylinder or caliper (however rear bks equipped) Naturally, check the entire line.

Jul 22, 2017 | 1996 Mercury Grand Marquis

1 Answer

Engine vacuum line diagram for 03 grand marquis 4.6


The vacuum line diagram is under the hood on the federal emissions decal. Any other vacuum related diagrams are in the Ford electrical and vacuum troubleshooting booklet. You can buy these used on eBay for less than $20.00 US

May 28, 2016 | 2003 Mercury Grand Marquis

1 Answer

How do I replace the rear axle assembly in a 2000 Mercury Grand Marquis?


If you have air suspension, turn it off from the trunk. Put car on hoist and support rear axle. Make sure you support the axel well so the coil springs do not injure you when you remove the shocks and etc. Remove brake lines from brakes. Remove emergency brake cable from brakes. Remove sway bar link bolts to frame. Remove the bolts that hold axle to rear control arms. Remove rear shocks. ( these are a real pain ) Axle assembly can now be removed.

Feb 09, 2015 | 2000 Mercury Grand Marquis

1 Answer

Need location of high pressure cutoff switch 97 mercury


The P/S is located to the rear of the compressor, it has a 4 pin round connector.

May 19, 2012 | 1997 Mercury Grand Marquis

3 Answers

Whats the procedure for bleeding brakes 2000 grand marquis


Bleed the master cylinder at the brake lines,then bleed right rear ,left rear,right front,and left front.

Jun 12, 2010 | 1998 Mercury Grand Marquis

1 Answer

1993 Mercury Grand Marquis, Brake fluid leaking under left rear door. Brake pedal goes to floor. How can i fix this?


Hi, the reason the pedal goes to the floor is because the brake line going back to the rear axle blew, first you will need to find where the hole is and cut out the bad section, usually you can find a clean spot further down that you can cut out the bad spot. you will need to go to the parts store and get a new piece of brake line and a tubing cutter and a double flare kit. usually you can rent one of these to save money.

May 22, 2010 | 1991 Mercury Grand Marquis

1 Answer

Grease has spun out soaking the caliper and brake lining on my mercury grand marquis 1994 with rear disc brakes.how do i repair this


you should replace the pad cause the will have absorbed the fluid, if the seal is good on the caliper they can just be cleaned, and wash the rotors wit brake clean, replace the axle seals and all should be ok

Nov 14, 2009 | 1994 Mercury Grand Marquis

1 Answer

I have a 2000 Mercury Grand Marquis and I'm trying to purchased the rear brake pads, but I don't know which ones to buy for my vehicle. What's the difference between a phenolic piston and steel piston....


What they are referring to is the caliper pistons. The phenolic should be plastic. You need to know what type of pistons your car has because there is a difference in the clips on the linings.

I also would recommend you to inspect the emergency brakes and if you are planning to keep your car the ceramic brakes are expensive but really quiet and no brake dust.

Nov 05, 2009 | 2000 Mercury Grand Marquis

1 Answer

1994 grand marquis


1). get a helper first. perferablility some one can follow instruction.
have the helper set in the car and ready to step on the brake pedal.
2). fill the brake cylinder to the max mark. have the helper step on the brake 3 times and hold it . while you open the bleeder valve at the wheel brake cylinder. Watch the brake fluid, wait till it just before it empty out, close the valve. and tell the helper to release the brake. do this till there is not air coming out, just steady stream of brake fluid. close the valve. and move to the other wheel.
IT IS IMPORTANT THE HELPER DO NOT RELEASE THE BRAKE PEDAL BEFORE YOU CLOSE THE VALVE. if that happen, you just have to keep doing it till all air are out.
3). start from the rear right, rear left, front right, front left.
4). maek sure the fluid in the master clyinder do not drop below the min line.
5). fill the master brake cylinder with fluid and ready to go.

Apr 28, 2009 | 1983 Mercury Marquis

Not finding what you are looking for?
1997 Mercury Grand Marquis Logo

Related Topics:

461 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...