Question about 2003 Hyundai Tiburon

1 Answer

4 cylinder motor

Do you have detailed instuctions or a visual guide on removing the motor from a 2003 tiburon with a 4 cyl. and a standard transmissin?

Posted by on

  • Anonymous Oct 15, 2008

    colors of wire conecting to sensor

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers

Http://www.analogstereo.com/pdf/om/hyundai_tiburon_owners_manual_2003.pdf
4 cylinder motor - note_icon.gif Mark all wiring and hoses to avoid misconnection. Inspection the timing belt before removing the cylinder head. Turn the crankshaft pulley so that the No. 1 piston is at top dead center
1. Disconnect the neagative terminal from the battery 2. Remove the engine cover. . Drain the engine coolant. Remove the radiator cap to speed draining. 4. Remove the intake air hose and air cleaner assembly. (1) Disconnect the AFS connector. (2) Disconnect the breather hose from air cleaner hose. (3) Remove the intake air hose and air cleaner. 5. Remove the upper radiator hose (A) and lower radiator hose (B). 6. Remove the heater hoses 7. Remove the engine wire harness connectors and wire harness clamps from the cylinder head and the intake manifold. (1) OCV(Oil Control Valve) connector (A). (2) Oil temperature sensor connector (B). (3) ECT (Engine Coolant Temperature) sensor (C) connector. (4) Ignition coil connector (D). (5) TPS (Throttle Position Sensor) connector (A). (6) ISA (Idle Speed Actuator) connector (B). (7) CMP (Camshaft Position Sensor) connector (A). (8) Four fuel injector connectors (B). (9) Knock sensor connector (C).

Posted on May 27, 2008

  • Kleanthis Mavropoulos
    Kleanthis Mavropoulos May 27, 2008




    (10)

    Disconnect ground cable (D) from the intake manifold.



    (11)

    Front heated oxygen sensor (A) connector



    (12)

    PCSV (Purge Control Solenoid Valve) (A) connector.



    8.

    Remove the fuel inlet from delivery pipe (A).



    9.

    Remove the PCSV hose (A).



    10.

    Remove the brake booster vacuum hose (A).



    11.

    Remove the accelerator cable by loosening the locknut, then slip the cable end out of the throttle linkage.



    12.

    Remove the power steering pump.



    13.

    Disconnect the inhibitor switch and solenoid valve connector (A).



    14.

    Remove the transaxle range switch connector (A).



    15.

    Remove the vehicle speed sensor connector (A).



    16.

    Remove the control cable transaxle range switch nut (A).



    17.

    Remove the clip (A) of the control cable.



    18.

    Remove the input shaft speed sensor connector (A).



    19.

    Remove the output shaft speed sensor connector (A).



    20.

    Remove the transaxle earth cable (A).

  • Kleanthis Mavropoulos
    Kleanthis Mavropoulos May 27, 2008




    21.

    Remove the start motor cable mounting bolt (A).



    22.

    Remove the starting motor connector.



    23.

    Remove the alternator connector.



    24.

    Install the SST(09200-38001), the engine support fixture and the adapter, on the engine and transaxle assembly.



    25.

    Remove the engine mounting bracket (A).



    26.

    Remove the transaxle mounting bracket (A).



    27.

    Remove the front tires.



    28.

    Remove the ABS wheel speed sensor (A).



    29.

    Remove the caliper and hang the caliper assembly (A).



    30.

    Remove the knuckle mounting bolts



    31.

    Remove the power steering return hose (A) and drain the power steering oil.



    32.

    Disconnect the rear oxygen sensor connector



    33.

    Remove the front muffler



    34..

    Remove the steering u-joint mounting bolt




    35.

    Remove the sub frame bolts





    36.


    Remove the engine support fixture and the adapter.




    37.

    Jack up the vehicle

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4 cylinder oxygen sensor does not fit my 2003 tiburon the rear sensor i had to use a sensor for a 6 cylinder but my car is a 4 cylinder


if it fits it will probably work, but make sure that the sensor is the correct type. there are at least two different types of sensors. check with your dealer for the correct type. if their part is too expensive, you can get less expensive substitutes somewhere else that will work well with your car.

Apr 03, 2010 | 2003 Hyundai Tiburon

2 Answers

Car jerks while taking off; changed fuel filter


get a scan tool to retrieve the dtc (diagnostic trouble code).
you will get a misfire code.
p0301 for cyl 1
p0302 for cyl 2 and so on.
i can't recall if that engine has plug wires or coil on plug but if its coil on plug replace the coil corresponding to the cylinder misfire

Jan 12, 2010 | 2003 Hyundai Tiburon

1 Answer

Have a 2003 tiburon gt 6 cyl driver side window doesnt work replaced brushes and still not working?


Check the power to the window motor, and also check the power to the window switch. The switches go out almost as regularly as the cheapo window motors hyundai supplies. If both are getting proper voltage, just order a new window motor. You can get them online for around $35.

Oct 31, 2009 | 2003 Hyundai Tiburon

1 Answer

Cant seperate trans from motor 2003 tiburon 2.0 manual all bolts removed


At the top of the transmission where the hydraulic clutch cylinder rod is attached, you have to remove the lever from the shaft (14mm nut), because the clutch is the 'PULL' type pressure plate bearing system. After you remove the trans, you will need to remove the bearing from the pressure plate and put it back on the input shaft collar in the trans before reinstalling the trans.

Oct 14, 2009 | 2003 Hyundai Tiburon

1 Answer

Need to know location oxygen sensor 2003 tiburon bank 1 sensor 2 to replace it


WHICH ENGINE?.. 2.0 four cylinder? OR 2.7 V6?
Anyway, sensor 2 is always 'downstream', so it's lower than all the others. V6? lowest near the firewall.. .4 cylinder?.. lowest near the radiator.

Sep 29, 2009 | 2003 Hyundai Tiburon

2 Answers

2003 4 cylinder 5-speed tiburon,engine just


This generally indicates a vaccumn leak, or sticking idle air control valve.

Jun 20, 2009 | 2003 Hyundai Tiburon

1 Answer

Location of the Purge Control Valve for 2003 Hyundai Tiburon


There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Jun 06, 2009 | 2003 Hyundai Tiburon

1 Answer

2003 tiburon transmission


if you have a 4 cylinder you wiggle the clutch shaft up and down remove the lever and this will get the fingers off the releasbearing / 2 starter bolts 2 large bolts up top 3 under exhaust and 4 0n the other side lower one is above right inner cv axle, remove left axle from car right axle can moved over un do ball joint 3 mounts remover upper side and reaar , strap engine to a cradle or 4,4 post chained to support engine you can slide tranmission over14 inches with room to stick your hands in and remove pressure plate ,fly wheel can be removed but takes good hands tricky,now thats a hyundai flat rate tech procedure for 4 cyl, IF YOUR NOT SURE ABOUT or if the engine is V6 cylinder THE SUB FRAME COMES OUT you can remove rack hose on sub frame and 4 bolts and wire or strap the steering rack to body at that can stay in car or you will have to take rack out with sub frame

Sep 25, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

789 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...