Question about 2005 Nissan Altima

1 Answer

Replace brake bulb on passanger side - 2005 Nissan Altima

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Remove the tail lamp from inside trunk should be three or four plastic screws caps holding it in whole light will pull out

Posted on Oct 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 Jeep Commander Tail light


The tail light circuit is separate from the brake and turn signal circuit. Either the bulb socket has gone bad or a wire has flaked out. Check for voltage at the socket on either pin base when you have your parking lights on. If voltage is present, it is either a worn socket failing to hold the bulb properly, or another bad bulb. If no voltage, determine which wire on the other side is tail light power, and run a new wire across to the side that isn't working and connect it to provide power.

Apr 09, 2014 | 2006 Jeep Commander

1 Answer

94 GMC Yukon when the lights are on the passanger side brake light dose not work but its fine when lights are off


Thats because it's a double element bulb when the lights are on one of the wires in the bulb is lit. Well when you step on the brake there is not another filiment in the bulb to light because it's burnt out, replace the bulb.

Sep 18, 2013 | GMC Yukon Cars & Trucks

1 Answer

2004 Hyundai santa fe brake lights on passanger side replaced bulb still not working


Dude you need to do a circuit test to check for power at the bulb socket with someone pressing on the brake pedal, or use a short stick wedged against the drivers seat.
Have you had a towbar fitted recently, these are a constant source of faulty connections !

Aug 19, 2013 | 2004 Hyundai Santa Fe

1 Answer

My passanger side break light will not work......


The light bulb has 2 operations, brake and tail lights. Go to Advance and they will replace it for you.

Feb 18, 2013 | 1999 Chevrolet Malibu

1 Answer

Passanger and third break light don't work, new bulbs and fuses installed. what should i check next?


I would check the turn signal switch first. The brake lights may go thru the switch depending on the configuration.

Aug 16, 2012 | 1992 Honda Accord

1 Answer

When i apply my brakes my passanger side brake light will not work i have replaced bulbs, switched the socket to the drivers side and it works, have not tried to change anything behind the brake pedal,...


You need a test light to check for power and ground at the bulb, does this truck have a tow package? Like a trailer plug? If so you need to look under the rear of the truck for the light wire harness and find where they tapped into this for the trailer lights, it may have a bad or dirty contact, or a broken ground wire to the frame, please advise and as always please rate this of leave feedback

Jul 31, 2011 | 2001 Dodge Durango

1 Answer

Passanger back brake light out but all other


Follow the wire harness down to the junction box were the wire harness plugs into under the truck adn ck for corrosion especialy if you live in a snowy area corrosion due to road salt.

Jan 17, 2010 | 2007 Chevrolet Silverado Classic SS New...

1 Answer

Passanger side turn signals don't work


First: press the brake and be sure that both sides light up. If one side does not, turn your attention to it. Remove the taillamp assembly from the suspect side and disconnect it. Unscrew the socket / circuit board and dismount it from the reflector. Take out the bulbs and examine the sockets, looking for melted / toasted / warped sockets. If they are bad, don't even bother trying new bulbs or attempting a repair; go to the parts store and get a new socket / circuit board assembly. Last I looked they cost about $25 apiece.

Nov 16, 2009 | 1988 Chevrolet K2500

1 Answer

1998 BMW 740i - I had a brake light out, replaced it, it won't


check where the wires go from the inside of the body to the out around the gromet. I did run into one that the wires rubbed. Also if the light are on the trunk lid check where they go through the trunk latch.

Sep 14, 2009 | 2006 BMW 750Li

1 Answer

How to replace third brake light on 1998 lexus es 300


in order to replaced the bulb, u go from inside the car (back Seat). The housing for the brake light will shift to the left (passanger side) then slide out, disconnect connector and replace buld

Apr 28, 2009 | 1998 Lexus ES 300

Not finding what you are looking for?
2005 Nissan Altima Logo

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...