Question about 1994 Hyundai Excel

1 Answer

No power on throttle , engine idles fine but wont rev cleanly or rev under load

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 417 Answers

Hi,
it may have jumped time. that may or may not give you a code for a code reader. how long has it been since its had a timing belt. remove the cover and check the teeth and condition, check all your vacuum lines while your doing that too.
jm

Posted on Oct 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E150 hesitates under light throttle


Did it occur the MAF (will not set code) is defective or the fuel pressure is low?

Apr 08, 2014 | 2003 Ford E150

1 Answer

Throttle assembly


Hi Jimmy ! THE PROBLEM YOU ARE FACING MOSTLY IS ON THE THROTTLE BODY . IS GOOD IF YOU KNOW WHAT YOU WILL DO BY REMOVING THE THROTTLE BODY FROM THE ENGINE. JUST GIVE IT A GOOD CLEANING BY USING A CARBURRETOR CLEANER-CLEANING THE THROTTLE ITSELF AND ALSO IF YOU CAN CHECK THE IDLE SPEED CONTROL WHICH IS UNDER THE THROTTLE BODY ( ONE UNIT) STRIPPED BY FOUR SCREWS, CLEAN AND REFITTED.

Feb 27, 2014 | 2000 Toyota Camry

1 Answer

1990 Buick Park Ave.


clean the idler on the intake and also clean the throttle sensor, it would also be best to change the air filter and clean the maf sensor. Idler does more than just idle vehicle it controls low revs, and drop down from reves. throttle sensor tell ecu what air to add to the fuel. and the MAF tells ecu how much air is coming into the intake. also check for broken cracked vacuum lines.

Jul 17, 2017 | Cars & Trucks

1 Answer

How to fix f85 codes in cadillac


this is what i found about code f85




QUESTION: 1991 Sedan Deville, 4.9 port injection
Car runs great until outside temp reaches 92 deg. or above. the car will start to cut out under load (take off or hill. if i pull over the car will idle fine rev the engine to a steady high rpm and it will cut out. i had a code e44 (o2 sensor rich)so i replaced o2 sensor with no effect. the other code received was f85 (Throttle body service required). I have checked all connectors and hoses attached to the throttle body. all ok. looking inside throttle body there ar two tubes under the flaps one is totaly restricted with a black buildup and the other partly blocked. Not sure what these tubes do and if that could cause engine to cut out when hot and under load. any ideas?

ANSWER: You found your problem which is this black residue which when hot turns to a jelly substance and blocks the idle air passage. You need to clean all that residue from the throttle body and do not forget to spray the small hole in the side of the throttle body just behind the throttle plate.

Dec 05, 2012 | Cars & Trucks

1 Answer

Engine starts and idles fine, but will not rev up (2001 Jeep Grand Cherokee 3.1 diesel auto)


If it was a fuel shortage the engine would rev but to limited speed. This is a lack of air to throttle body. Check for clogged air filter and all the piping and the throttle body.

Sep 28, 2012 | 2001 Jeep Grand Cherokee

1 Answer

Engine idles perfectly and revs fine while in park. Under load the engine cuts out hard while accelerating at about 2000 rpm. Recently has had new throttle body, checked vac lines and actuator on air...


ur having fuel supply or poor electrical supply problem thats why the engine cuts off underload/ check spark plugs or airflow meter condition as well....

Apr 08, 2010 | 2003 Nissan Pathfinder

1 Answer

Starts O.K. Lacks pulling power. Will not rev to full power.


check for a clogged exhaust look at catalytic converter it could be stop up.

May 24, 2009 | 1999 Suzuki Vitara

1 Answer

Engine light on wont go over 3000rpm or under 2000rpm


Try the IAC valve this regulates the idle.

May 22, 2009 | 1998 Mitsubishi Galant

Not finding what you are looking for?
1994 Hyundai Excel Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...