Question about 2000 Toyota Celica

1 Answer

Key buttons will not operate locking system,i have changed battery but still no good.use master key,gets me into the car but alarm goes off and also when i attempt to drive it.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem kinda. Lost my master key and sent my ecu off with a home made 2 button key to program immobiliser. This key works to start the engin and drive but I cannot get the key to program with the alarm and locking system. You can try the following steps as may work for you.

I can get my car into programming mode after step 1 but step 2 does not work for me. The locks do not go off at all, not once or twice. Battery in remote key is fine as LCD lights red.

Can anyone help please?

Toyota celica 2000 - 2005 remote keyless entry programming guide
STEP 1
1. Key out of the ignition. Open the drivers door , all other doors are closed . Driver door is unlocked

2. Perform these steps within 5 seconds
a. Insert the key into the ignition ( do not turn it ) take key out
b. Insert the key into the ignition ( do not turn it ) take key out

3. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Insert the key into the ignition ( do not turn it ) and pull it out.

4. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Close drivers door.
d. Insert the key into the ignition and leave it in the ignition.
Turn the ignition to on (as far as you can go without turning the engine over ), then back to off .
e. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

STEP 2 (Does not work for me)

6. Perform these steps within 40 seconds
a. Press the lock and unlock buttons on the transmitter simultaneously for 2 seconds
b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.

7. Open drivers door

Hope this works for you.
Hayley

Posted on Nov 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

5 Answers

Security light flashes and it won't start


top
CODE ALARM SYSTEM
information is always subject to change and correction Used on:
Impreza 1996-2001
Legacy 1995-1999
Forester 1998-2000
codealarmremote2.jpgBattery GP-23A
Lock: Left button will lock all doors. Double chirp indicates locked.
Unlock: Right button will unlock driver's door only. Hold unlock button app 6 seconds, it will unlock all doors including rear gate. Single chirp indicated unlock.
If the car chirps or lights flash 4x the alarm was triggered.
Panic. Press both buttons to activate emergency honk and flashing lights.
Valet mode: With optional alarm only Press the red alarm button on the left of the steering wheel. The light will quickly double flash. To re-set back to normal mode, press the red alarm light button again

Battery failed and lights flashing?
Parking lights will flash when the vehicle's battery is disconnected and reconnected.
To stop lights from flashing, either:
Press remote transmitter “UNLOCK” button once OR turn the ignition switch to the “ON” position and press programming button for one second (see below).
The vehicle interior (courtesy) light and door open warning light (DOOR AJAR indicator) will then illuminate for 60 seconds when the ignition is turned off, or until the doors are locked with the remote transmitter. Yes, the dashboard instrument panel lights will flash when the parking lights flash.
Programming or Overriding the Alarm when you have lost the remote
Open driver's door.
Turn ignition key to 'On'
Press and *hold programming button* in (see diagram, button under dashboard)
After 15 seconds the the door locks will cycle 3 times. Do not release Programming button
Press lock (left) button the remotes to be programmed. The door locks will cycle one time.
Exit programming mode by releasing Programming button under dashboard and turning key to off.

codealarmremote1.jpgCode Alarm Programming Button is under dashboard on the kick panel by the driver's left knee, left of the steering column. If you can't find it, it might still be tucked up in the wiring harness higher up in that same general area. The botton is recessed in a plastic ring (see diagram).
This button must be pressed while programming remotes or if the battery was disconnected and the lights are flashing.
top

Jul 10, 2008 | 1996 Subaru Legacy

2 Answers

I have a 2005 colbalt ..i dont hv the remote key..everytime i open the door with key or not alarm goes off..first like a horn sound then louder it goes off and sometimes not untill u turn key on


thats how its suppose to work the key resets alarm ==by a fob online for a few dollars and program to car [free program] ==when you use key to unlock and enter vehicle you have a few seconds after opening door to turn vehicle on or start it and doing so resets alarm when you leave vehicle and lock it alarm is active

Jul 25, 2016 | Cars & Trucks

1 Answer

The unlock button on key wont work, when i use the key to open door the alarm goes off. The car drives but doors lock when I am inside and alarm goes off when I get out?


Have you changed the battery over on the key fob? If you key doesn't have a battery in it, then the chip in the key may be bad or the key may need to be re-synced with the cars ignition module.

Sep 13, 2015 | 1999 Toyota Corolla

1 Answer

Change the battery on a 2005 kia sedona key alarm


Try disconnecting the neg. battery terminal. Open the drivers door and leave it unlocked then reconnect the battery back up.

Oct 21, 2014 | Kia Sedona Cars & Trucks

1 Answer

2007 Chevy Aveo Key fob will only lock the doors


try changing battery in the remote

Nov 13, 2013 | Cars & Trucks

1 Answer

Had to replace battery in car..now the alarm goes off if you open the door or try to start the car , it sets it off. The car won't even start! help


Synchronization
When
Key buttons operated repeatedly while vehicle out of range and system becomes inoperative.
How
Carry out the following within 1 minute: Press key lock or unlock button for approximately 1 second. Manually lock or unlock vehicle. System should now lock or unlock vehicle. If not, carry out programming procedure.
Programming
When
Key added or replaced. System malfunction.
How
Switch ignition ON. Insert key to be programmed into driver's door lock. Lock vehicle manually. Press lock or unlock button. Wait at least 1 second. Press lock or unlock button again. Vehicle horn sounds to indicate correct programming. Remote controls can also be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed.

Mar 07, 2010 | 1998 Volkswagen Beetle

1 Answer

Replaced battery now having problems with automatically locks


Synchronization
When
Key buttons operated repeatedly while vehicle out of range and system becomes inoperative.
How
Press key lock or unlock button for approximately 1 second. Manually lock or unlock vehicle. System should now lock or unlock vehicle. If not, carry out programming procedure.
Programming
When
Key added or replaced. System malfunction.
How -

98MY
Keys can only be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed.
How - 99MY

Switch ignition ON. Insert key to be programmed into driver's door lock. Lock vehicle manually. Press lock or unlock button. Wait at least 1 second. Press lock or unlock button again. Vehicle horn sounds to indicate correct programming. Keys can also be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed.

Feb 05, 2010 | 2002 Volkswagen Passat

2 Answers

E36 BMW 318I CENTRAL LOCKING A. I bought a 2nd hand 1995 BMW 318I in South Africa. Good condition. No owner?s manual. Everything worked ok for a few months. Then the batteries of the remote key transmitter...


try locking and unlocking the car with the key 3 times slowly ,other than that i have no idea ?? another trick is to disconnect battery and join the cables together for a few minutes to discharge any capacitors that may be holding a charge in the computer..Only other thing i can think of is the main dealers who have the right connectors and software to re set it all .sorry i havent been of any help

Aug 04, 2009 | BMW 318 Cars & Trucks

1 Answer

2000 Toyota Corolla wont start Changed 02 sensor disconnected bat


I had the same problem, i had to remove the whole alarm system to get my car to start, when you unattatch the battery cables, the alarm notices the battery drain and sets the alarm off, i have no idea how much the dealership would charge for a new remote, but im sure its pricey, i would recommend just removing the alarm system, temporarily, until you can get a new remote. Good luck and god bless

Apr 17, 2009 | 1998 Toyota Corolla

Not finding what you are looking for?
2000 Toyota Celica Logo

760 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...