Question about 1998 Ford Escort

1 Answer

How to remove ford escort 1.8 diesal engine crank case and fitting details

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

FORD 2.0 MAZDA DIESEL ENGINE.YOU REMOVE CRANKCASE.FIRST DISCONNECT NEGATIVE BATTERY CABLE.RAISE AND SAFELY SUPPORT VECHICLE ON JACK STANDS.DRAIN THE ENGINE OIL.REMOVE THE BOLTS THAT ATTACH THE OIL PAN TO THE ENGINE AND REMOVE THE OIL PAN.CLEAN ALL GASKET MOUNTING SURFACE.APPLY A 1/8 INCH BEAD OF SILICONE SEALER ON THE OIL PAN MOUNTING SURFACE.INSTALL THE OIL PAN AND TIGHTEN THE BOLTS TO 5 - 7 FT LBS.

Posted on Oct 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set crankpully on 1989 Ford escort 1.9 liter engine for timing set up


most crankshaft pulleys ( harmonic balancer ) are keyed onto the shaft and held there with a bolt
in that case the timing mark will always be in the right place
otherwise set the no 1 piston on tdc (remove no 1 spark plug and with a bit of light gauge wire move the crank until the piston comes up and then starts to go back down)
the mark on the balancer should be at the tdc mark on the timing case cover

Oct 07, 2015 | Ford Cars & Trucks

1 Answer

Video on replacing motor mounts on a 1999 ford escort


I have no video of the job just written instructuions.

  • Park the vehicle on level ground and shut off the engine. Raise the front end of the Escort off the ground using the floor jack. Lower the vehicle onto jack stands placed under the frame to support the car.
  • 2Place the jack under the oil pan and raise the lift plate to the bottom of the oil pan. Remove the engine mount bolt using the 1/2-inch socket wrench. The engine mount bolt is in the center of the mount fitting in clear view.
  • Slowly raise the engine using the jack until the weight of the engine is removed from the engine mount. Pull the engine mount from the fitting and place the new mount in the fitting.
  • 4Lower the engine slowly and insert the bolt into the mounting hole. Tighten the mount bolt to 67.9 foot-pounds using the torque wrench.
  • 5Remove the bolt from the other engine mount the same way as the first one. Pull the mount from the fitting and insert the new one. Replace the bolt to the center of the mount fitting. Lower the engine to the frame and tighten the mount bolt to 67.9 foot-pounds.
  • 6Remove the jack from under the Escort. Raise the car off the jack stands, remove the stands and lower the car to the ground
  • Jul 19, 2012 | 1999 Ford Escort

    1 Answer

    Spark Plug Wiring Diagram For 1994 escort


    Firing order is 1-3-4-2
    Remove no 1 cylinder sparkplug(furthest from the transmission). Block the plug hole with your hand. Rotate the engine with a wrench until you feel pressure under your hand. No 1 cylinder is now on compression stroke.
    Now get the engine on TDC(Line up notch on the crank pulley with the timing pointer). Remove the distributor cap. The rotor arm will be pointing at no 1 cylinder plug wire. Moving clockwise connect the wires.
    59dec26.jpg

    Sep 23, 2010 | 1994 Ford Escort

    1 Answer

    How to fit a alternator belt on a 1.8 diesal escort van 51plate


    This should be the same as a car, jack the front of the car up put stands under, remove front wheels, remove bottom cover (about 7 screws), Remove powersteering pump pully 3 bolts, remove and refit new belt and P/S pully, you might get away with not having to adjust alt but if you have to youll need a 13mm spanner to undo the locking bolt then pull the alt tight (its really tight u might need a bar), once all done replace in reverse order.

    Dec 16, 2009 | 2001 Ford Escort ZX2

    1 Answer

    Location of timing pin plug 99 ford escort zx2 2.0 dohc


    A p1383 code stands for (Variable cam timing over retarded Bank 1) Hope this helps.

    Jun 14, 2009 | 2002 Ford Escort

    2 Answers

    My escort van is out of timing need to set timing again


    YOU NEED TWO 6MM DRILL BITS, THERE ARE TWO HOLES TO PUT THESE IN, ONE ON THE CAMSHAFT AND THE SECOND ON THE PUMP. SLOWLY TURN THE ENGINE BY HAND UNTIL THE TWO HOLES LINE UP WITH HOLES BEHIND THEM, THEN PLUG WITH THE DRILL BITS. ITS NOW SAFE TO REMOVE THE BELT BY TAKING OFF THE TENSIONER AND LOCKING OFF. PUT ON THE NEW BELT AND RELEASE THE TENSIONER SLOWLY AND REMOVE THE DRILL BITS. TURN THE ENGINE BY THE NUT ON THE CRANK SHAFT A COUPLE OF TIMES. THEN PULL BACK THE TENSIONER ALL THE WAY, THEN LET IT GO SO IT SNAPS AGAINST THE BELT, IT IS NOW TENSIONED AND JOB DONE

    Feb 28, 2009 | 1999 Ford Escort

    1 Answer

    Glow plugs ford escort diesal 1.8


    Since you're running diesel, you might need an engine block heater. Even the largest vehicles need to keep the block warm when the winter temperatures drop. It keeps the engine oil & fuel looser.

    Jan 05, 2009 | 2003 Hyundai Santa Fe

    1 Answer

    What are the timing marks 4 a ford escort 1996 1.8 turbo diesal


    you need a pin for the crank(just behind alt/power steering bracket,a plate for the camshaft under rocker cover at the rear and a pin for the pump which slides in at the 12 o clock position

    Dec 28, 2008 | Ford Escort Cars & Trucks

    1 Answer

    1996 Ford Escort 1.9L hatchback engine cranks but doesn't start.


    if the fusebox is above accelerator pedal its relay number 1 .best of luck.

    Sep 27, 2008 | 1996 Ford Escort 4 Door

    Not finding what you are looking for?
    1998 Ford Escort Logo

    140 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    74945 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5467 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...