Question about 2000 Buick Century

1 Answer

2002buick century is there a way to manually raise passinger front power window cant get new motor reg for 2 wks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Light for gear shift

Posted on Aug 29, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace rear window power regulator motor


First, make sure the problem is the motor itself. Remove the interior panel and check that the switch is getting power and that it's sending it to the motor-use a test light. If the power is ok raise the glass all the way up and duct tape it in place. Disconnect the electrical connector from the motor and drill out the factory rivets. The new motor should come with bolts to replace them. Unhook the motor from the regulator and remove it. New motors are not too expensive and all parts houses (autozone,oreillys) should stock them.

Aug 11, 2014 | 1995 Buick Century

1 Answer

How do I manually raise the window on power window


Could be switch. If you can access you may be able to "jump" or override the switch. otherwise take inner door panel off and do the same directly to the motor.

Nov 17, 2012 | 2001 Ford Taurus

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

'92 Buick Century s/w -- Both front power windows will lower, but will not raise. Rear windows work OK. What is my most likely problem? Thanks!


find front window regulators for your car, buy them and pay a glass shop to install them. stay away from dealer, you can buy regulators at parts stores and eBay. 10 years is about it for a regulator, do not buy used.

Jan 19, 2011 | 1992 Buick Century

1 Answer

How to remove drivers door panel on 99 buick century . I need to see why power window will not roll all the way up. seems to be off track


GET SILACONE SPRAY AND WET FRONT AND REAR RUBBER TRACKS THE WINDOW RUNS IN LIBERALLY..IF IT THEN WORKS ...REPEAT EVERY 2 WEEKS..IF THIS DOESN'T HELP YOU PROBABLY NEED A NEW WINDOW MOTOR.

Mar 20, 2010 | 1999 Buick Century

3 Answers

The power window does not work. There is a cable


you buy the whole window regulator with motor and it bolts in 5 screws and the motor has 1 plug in harness just hold the window in place once you take out the reg it may fall ? a wedge peice of wood works well

Aug 26, 2009 | 2001 Buick Century

1 Answer

Power windows only go down 2 inches then stop,


1ST TRY LUBRICATING THE WINDOW CHANNELS WITH SILICONE SPRAY, IF THAT DOESN'T WORK U WILL NEED NEW WINDOW REGULATORS.

Mar 16, 2009 | 1989 Buick Century

1 Answer

Motor mount


Yes this mount supports a lot of the motor. It also supports the transmission so if you are on a down hill slope the motor will roll forward and cause a lot of pressure on the front mount. Hope this helps.

Aug 10, 2008 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
2000 Buick Century Logo

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...