Question about Chevrolet TrailBlazer

1 Answer

How do you take fan & other parts off waterpump

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,072 Answers

Sockets,wrenches,hammer, possible a flat tip and a wheel pulley. Drain the fluid then you will need to take the belt off first note the routing of the belt draw it write it down take a picture, you can just loosen like the alternator or whatever you feel comfortable with, take the belt off. remove the bolt from the water pump pulley and with the wheel pulley pull off the pulley, remove bolts from housing, tap on housing and it should pop off. The same with a fan just be careful not to crack it. hope this helped tim

Posted on Oct 03, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

V6 3.0 getting hot

thermostat is on the waterpump. Follow the lower radiator hose to the housing. there should be three 10mm bolts should be holding the housing to the waterpump with the thermostat in between. If you are going to change it, then drain your cooling system first.

Mar 18, 2013 | 1992 Toyota 4Runner

1 Answer

2000 Cadillac Seville overheating-- Replaced the waterpump,removed the thermostat and replaced the radiator cap, and still overheats.The fans seem to run on low speed,do they have a high speed ? I have...

Wasn't all that work done at a repair shop?

And weren't all the questions addressed when you
got it back or called & asked since you still have issues?

Replacing parts is not diagnosing the issues, only testing the
vehicles systems to see what does work correctly & then
what doesn't

Feb 07, 2013 | 2000 Cadillac Seville

1 Answer

Fan clutch waterpump radiator and timing belt replacement

Without more specifics, the only thing I can suggest would be for locating the parts you need. I'd recommend a salvage yard for any of your parts EXCEPT the waterpump. I owned a salvage yard and still recommend replacing the waterpump with a new (not rebuilt) unit. The costs are almost the same in almost all applications. If you have nowhere at all to work on the car, a cheap alternative to a repair shop is a tech school. You supply the parts and pay little or no $ for labor. Food for thought anyways. Good luck!

Jan 10, 2012 | Toyota Pickup Cars & Trucks

1 Answer

Where is the water pump located? I had something blow and its leaking raidaitor fluid around pully system? What do I need to take apart to find the water pump?

Your fan & pulley are bolted to the waterpump. You need to remove plastic fan schrod, then fan, pulley, belt then you will see waterpump bolted to front of engine. Stop by any good parts store, have them look up waterpump and show you what it looks like. Then you'll know what to look for.

Feb 23, 2011 | 1994 Mercury Villager

1 Answer

Anti freeze is leaking between the motor and the fan housing , what are the possible causes ? It looks like part of a round rubber gasket is hanging out ?

Sounds like your waterpump has gone bad. Could be fan belt broke that drives waterpump (would explain large rubber pce hanging out) Have a reputable shop look at it for you.

Jan 08, 2011 | 1997 Jeep Grand Cherokee

1 Answer

I believe the bearing on my waterpump is bad. while driving the fan began rubbing the shroud and eventually wedged against the waterpump pulley. before removing the radiator,shroud and hoses i checked...

You can't remove the fan and pump together. The pulley will be i nthe way. You must remove the fan and clutch, then the pulley then you will have access to the water pump bolts as well as the other components which must be removed to get the pump off.

Feb 22, 2010 | 1999 Ford Ranger SuperCab

1 Answer

How to install a waterpump on a 1987 mercedes 300e ?

First of all, remove the water hose pipes, unclip radiator, lose the fan belt (see the tightening screw at the back of the generator), remove the fan belt (remember the sequence to reinstal), unsrew the fan bolt and take the fan off, then remove radiarot, behind the radiator, there is the water pump screwed by 6 bolts, unscrew the bolt and u will get that! Hope this will solve the problem

Sep 13, 2009 | 1987 Mercedes-Benz 300-Class

1 Answer

Replacing waterpump 1991 chrysler imperial

You might want to try ( & sign up for free and you get access to step by step manuals & parts prices.

Mar 16, 2009 | 1991 Chrysler Imperial

2 Answers

Waterpump removing fan

Well, if it's a 5.0L engine, remove the 4 bolts holding the fan to the pulley. If it's a 4.0L engine, you need to hold the waterpump pulley still and break the nut loose holding the fan clutch to the waterpump. If you don't have a wrench that big, try using a long chisel on the edge of the nut and hitting it very hard with a hammer to break it loose.

Feb 15, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides